Jump to content
SAU Community

Group Buy # 3 Arospeed Adjustable Cam Gears, By Popular Demand


Recommended Posts

  • Replies 240
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Is the inlet cam gear *exactly* the same as the exhaust cam gear?

If it is, does anyone want to buy a gear?

I've put my name down for a pair of gears, but after doing more researching and buying a powerfc which will control timing on the inlet side, i think i only need to adjust the exhaust side to get some extra K W 's. Is this right???

So are the exhaust and inlet gears exactly the SAME or DIFFERENT?... Can any one pls confirm?...

I'll take a pair if anyone backs out.. PM me R33kid or anyone who decides they dont want either.

Cheers

Karl

Hi Karl,

I have sent you a PM..

BUT, if anyone else is interested.. I'll have a spare set up for sale when these gears arrive because I have decided to keep one engine for spare parts :P

You'll have a choice of Red or Blue as I ordered 2 sets of each..

Let me know if anyone is interested..

Regards,

Sherwin

good news cam gears have arrived and are in customs. should be any day now.

r33kid - are the inlet gears the same or different from the exhaust gears?

r33kid - are the inlet gears the same or different from the exhaust gears?

Hi there,

I'm pretty sure they're EXACTLY the SAME!

I don't see why there would be a difference..

Hi Karl,

I have sent you a PM..

BUT, if anyone else is interested.. I'll have a spare set up for sale when these gears arrive because I have decided to keep one engine for spare parts :)

You'll have a choice of Red or Blue as I ordered 2 sets of each..

Let me know if anyone is interested..

Regards,

Sherwin

Im dead keen on a blue set if they will fit R32 GTS-t :wave::wub::)

Im dead keen on a blue set if they will fit R32 GTS-t :O;):O

I've sent you a PM..

Let me know what you think :)

UPDATE

Red cam gears in my hands will despatch ASAP

Blue cam gears still in customs, lazy bastards but hope to have by end of the week for despatch.

UPDATE

Red cam gears in my hands will despatch ASAP

Blue cam gears still in customs, lazy bastards but hope to have by end of the week for despatch.

Like usual R33kid,

I'll leave trader feedback when I recieve the gears :P

If anyone has a blue exhaust cam gear for RB20 left over pls let me know. I will take one

Cheers :)

So when should red purchased gears arrive to the Melbourne buyers?

;) I could of forged my own gears by now. :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...