Jump to content
SAU Community

Recommended Posts

I changed the fuel filter at 100, 000km and the car has now done 137,400...is it due or do they last for 100,000km

I think your getting confused with the timing belt mate. Fuel filter should be changed approx. every 5000 to 10000kms. Oil filter should be changed approx. every 5000Kms. Timing belt is a major service which is usually changed every 100,000Kms with the idlers and tensioners i believe. Good luck :laugh:

i don't think you need to change your fuel filter that often.

it depends on how often you run on a low tank. if you don't let the car get below about 1/3 tank then you can leave it longer than someone who constantly runs it below 1/4 tank.

Edited by mad082
i don't think you need to change your fuel filter that often.

it depends on how often you run on a low tank. if you don't let the car get below about 1/3 tank then you can leave it longer than someone who constantly runs it below 1/4 tank.

I thought the fuel pump sucks fuel from the bottom of the tank anyway.?.

I agree with GTR chick, every 4000km's is a nice ammount.

I just dont understand how people put off chaning their oil every 5-10,000km's.

Its a $45 bottle of oil for gods sake, its cheap insurance, i keep my baby bathing in new motul every 3000kms.

probably less if i involve spirited driving.

cheers

Mine swallows $60 worth of Motul every 5000km's + a $16 PureOne oil filter.

Every fuel filter I do the airfilter also (Purulator airfilter)

Still running the stock airbox but with a nice big arsed 100mm cai.

if i did mine every 3000k's that would be after only putting through 500L. seems kind of a waste. if you used a handfull of gravel as octane boost then i could understand changing it as often as your oil.

to see how little fuel that is, a common fridge is about about 450L. so if you had a tank the size of your fridge you would be changing it after only putting through that small amount of fuel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...