Jump to content
SAU Community

Recommended Posts

Just purchased a '90 model R32 GTST over the weekend. The car struggles to start when its stone cold.

Quick run down of what happens:

Turn the key and hold for about 2 seconds, engine doesnt fire

Turn key again and hold for another 2 seconds

Engine fires but will idle at about 500rpm and sounds like its about to stall

within 3-4 seconds the rpm will rise and idle as per normal.

This is only when the car is stone cold, even if i go for a drive then turn the car off and come back half an hour later it will fire first go. When the car is up to temp it runs perfectly otherwise until its up to temp, its a bit rough.

Anyone have any ideas?? I was thinking it may be a vacume line or something?

Regards,

Ari

Link to comment
https://www.sau.com.au/forums/topic/147758-cold-start-struggle/
Share on other sites

omg i have the exact same problem on my r33 series2, only happens in the morning when cold, fuel pump was checked by mechanic and is completely fine. Someone know what this might be? :D

*i have new spark plugs, new o2 sensor etc & service done* My mechanic couldn't find the problem.....

Edited by NeesaanGTS

i think it is just the fuel pump needing to prime.

mine does the same thing on cold starts.

try leaving the key in the on position for a few seconds before you start it and see if it then starts easier. this gives the pump a chance to prime.

dude i got the same prob in my 93 r32 gtst type m it does sometimes work if i leave the key on reds for 5 seconds but other times it chokes if anyone finds the reason please tell me its annoying me to the shit house lol .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...