Jump to content
SAU Community

New Dash Console - Pics

sky017

By sky017,
in Exterior & Interior Styling

 Share

Recommended Posts

TramanBaba Community Regular

TramanBaba

Posted
Posted
hey guys im a brand new skyline owner.

was lookin through this thread, some awesome results here and seeing as how my interior is a bit rough i just have to do this too.

ive got a bit of a noob question though... how do i remove the dash panels? i dont wanna break anything so i thought i'd ask first.

I'm thinking a dark silver might go well with a black skyline. What do you think?

thanks!

There are posts in teh DIY section... Anyways you need to pull the panels out, disconnect the main housing panel, i.e. various plugs that you just be able to clip out and that's about it really. For the driver's arm control removie the plug in the cup, unscrew it and pull it out carefully. If you need pics I could email them you. Good luck. To the thread starter.. once again this really is a fantastic thread. For the cost you get soo much more value and satisfaction. Cheers.

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Rudager Enthusiast

Rudager

Posted
Posted (edited)

Had a go today, completly botched it, musn't have shaken the primer enough and was spitting everywhere, didn't use a high enough sandpaper so got fairly noticeable scratches everywhere.

So gunna goto supercheap tomorrow (hope they're open) get some 100,200,400,600 and 2000 grit sandpaper, another can of primer and the silver paint i picked out. Sand off all the old paint then work it up from 100 to 2000 grit to get a nice smooth surface, 2-3 coats of primer 2-3 coats of Mercury Silver or whatever it was and 2-3 coats of clear coating.

Will let you guys know how it turns out :sick:

EDIT: Just a quick question, how is everyone supporting the parts while they paint them, i've just had them lying on the ground, just so hard to get a nice even coating though, was going to hang it from the clothsline but it's right under a tree and didn't want shit falling off it

Edited by Rudager
TramanBaba Community Regular

TramanBaba

Posted
Posted
Had a go today, completly botched it, musn't have shaken the primer enough and was spitting everywhere, didn't use a high enough sandpaper so got fairly noticeable scratches everywhere.

So gunna goto supercheap tomorrow (hope they're open) get some 100,200,400,600 and 2000 grit sandpaper, another can of primer and the silver paint i picked out. Sand off all the old paint then work it up from 100 to 2000 grit to get a nice smooth surface, 2-3 coats of primer 2-3 coats of Mercury Silver or whatever it was and 2-3 coats of clear coating.

Will let you guys know how it turns out :sick:

EDIT: Just a quick question, how is everyone supporting the parts while they paint them, i've just had them lying on the ground, just so hard to get a nice even coating though, was going to hang it from the clothsline but it's right under a tree and didn't want shit falling off it

yea i did mine last week and had them lyin on teh garage floor. Turned out fine. Make sure you spray one section at a time. Don attempt to spray a whole piece in one go with the finger on the nozzle. results don turn out good that way. Anyways supercheap will be open tomo ( i enquired, need to get a jack off them :D). good luck with your rejob.

ak_stylez Community Regular

ak_stylez

Posted
Posted (edited)
There are posts in teh DIY section... Anyways you need to pull the panels out, disconnect the main housing panel, i.e. various plugs that you just be able to clip out and that's about it really. For the driver's arm control removie the plug in the cup, unscrew it and pull it out carefully. If you need pics I could email them you. Good luck. To the thread starter.. once again this really is a fantastic thread. For the cost you get soo much more value and satisfaction. Cheers.

hey I'm having trouble with this part here:

http://members.iinet.com.au/~ahmedk/07-04-07_1412.jpg

how can i disconnect the switch and light so that the panel can come out? also same problem with the antenna switch on the other side of the steering wheel.

on a side note, how many of you had missing screws behind the ashtray etc? :D

thanks!

Edited by ak_stylez
Rudager Enthusiast

Rudager

Posted
Posted
hey I'm having trouble with this part here:

http://members.iinet.com.au/~ahmedk/07-04-07_1412.jpg

how can i disconnect the switch and light so that the panel can come out? also same problem with the antenna switch on the other side of the steering wheel.

on a side note, how many of you had missing screws behind the ashtray etc? :thumbsup:

thanks!

The mirror switch i got a flathead screwdriver and lever'd it out from the front, just be careful not to put too much pressure on the dash plactic's.

TramanBaba Community Regular

TramanBaba

Posted
Posted
hey I'm having trouble with this part here:

http://members.iinet.com.au/~ahmedk/07-04-07_1412.jpg

how can i disconnect the switch and light so that the panel can come out? also same problem with the antenna switch on the other side of the steering wheel.

on a side note, how many of you had missing screws behind the ashtray etc? :thumbsup:

thanks!

yup just lever it out with a flathead screw driver. It shouldnt take too much effort to get it out. Then disconnecthe plug for the mirror controllers. Am sure you'll have something similar for the alarm LED as well. And I dont know about others, but i have my ashtray screws intact :)

Basti Grand Master

Basti

Posted
Posted

no need for a flathead. just reach behind and squeeze the clips on the back together. should make it pop out. no worries bout scratches that way. its how i did it from memory. if you want confirmation im gonna be pulling my dash out on either monday or tues. can tell u for sure then.

with the light, if it isnt obviously slotted in then just cut the wire behind it. no harm to ur alarm and easily reconnected later

  • 8 months later...
XRAIDER Enthusiast

XRAIDER

Posted
Posted

I finaly got around to doing mine, didn't use a clear coat and it shouldn't scratch. Went a bit further and painted the cluster surround and the climate control panel.

I want to paint the passenger air vent and all passenger window switches one day to finish it off, but this will do for now. :)

Before and after pics

post-33491-1197100976_thumb.jpg

post-33491-1197101034_thumb.jpg

post-33491-1197101115_thumb.jpg

post-33491-1197101177_thumb.jpg

P.S The Taco is stuffed i tried to fix it it worked for a day then stopped again doh!

XRAIDER Enthusiast

XRAIDER

Posted
Posted
XRAIDER i like that job man. any reason y u didnt go the clear on top? oh and you forgot the ashtray

Hey thanks buddy, I didn't want a clear coat mainly because of the sun reflection, and I ran out of paint just as I finished off the climate control panel, I'll do it when I do the passenger door switches and the passenger vent.

Cheers :D

  • 1 month later...
Endorean Proficient

Endorean

Posted
Posted

Just a quick one, I've read through the post and have not found the answer.

How are you taking the rubber coating off the dash parts before painting. I want to try the Model paint method that was mentioned previously in the thread.

Cheers.

Basti Grand Master

Basti

Posted
Posted

i used sandpaper. bad idea this. lots of work and i had a lot of scratches left to fix afterwards. try either metho or turps. one or the other causes the rubber to deform, making it easy to remove. i found this out rite at the end.

  • 2 months later...
uneek Enthusiast

uneek

Posted
Posted

Well I've done my dash and other surrounds. Wont be doing it again in a hurry, but I did scratch it putting it back in...so maybe next Easter. Looks like I've gone a step further and done the door handles and side pockets of the door as well as the vents. I'd also like to do the demister vents, but have really had enough of this entire process!

I rubbed most of the rubber off by hand. Metho works and so does Acetone, but you still need to give it some elbow grease. Few coats of primer, few coats of paint and quite a few coats of acrylic top coat clear.

Main dash

post-47247-1206168499_thumb.jpg

Driver door

post-47247-1206168525_thumb.jpg

Passenger door

post-47247-1206168542_thumb.jpg

Fairly impressed with the result.

  • 7 months later...
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...