Jump to content
SAU Community

Recommended Posts

  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

thats for the gti-r

it depends on what skylineyou want to compare it to....r32,r33,r34??

Nissan Skyline R32

GTS-T/GTS-4

PRICE: $17K - $35K RWD

DRIVE YEAR: 89-93

ENGINE: RB20DET 2.0 DOHC 24V turbo 6cyl

WEIGHT: 1290kg

POWER: 160kW

TORQUE: 263Nm

0-100: 6.9

0-400: 15.01

Nissan Skyline R33

GTS-T/GTS-4

$20K - $46K

RWD

94-98

RB25DET 2.5 DOHC 24V turbo 6cyl

1370kg

184kW

274Nm

6.2

14.37

Nissan Skyline R34

GTS-T

$50K - $80K

RWD

98+

RB25DET

2.5 DOHC 24V turbo 6cyl VVT

1410kg

206kW

343Nm

6.0

15.00

taken from nissansilvia.com

The GTi-R also uses quad throttle bodies and is giving you around 30kw more in stock form that an S15

As cereal said as funky as S15's are, putting an S15 motor in a Gti-R is

A) ****ing expensive due to cost of S15 engine

B) A downgrade in power

And no, dont believe S15 box will fit either due to 4wd

Originally posted by lixid

ok

well are there many pulser gtir on the market, and are the parts easy to source as well??

because i don't see many gtir on the sydney road

I don't think you should have too much of a problem finding parts for a gti-r, but they probably wont be nissan parts......you'll be able to get Jap performance parts no problems.

There aren't many of them on Sydney roads because there aren't many of them on any roads........Only 4500 of them were ever made.

When I had the cash money for my car I was flipping up for either a GTS-t or GTi-R. The skyline won by a hair.

I'd admit that the Skyline won alot due to looks, as I got turned off the GTi-R everytime I saw the rear end of it...

Does anyone know of anyone who makes a body kit for these things ? NOT over the top. Just like side skirts and maybe a slighly revised rear bar ?

Some parts from the N14 Pulsar do fit...."SOME"

An early HPI had a review on one of them...Interesting. There ARE too many R33 Taxi's doing the rounds these days...

A mate of mine at work has a gtir & i got a r32 skyline.

We usually try 2 get a red light so we can have a mini drag, goin home from work. The gtir kicks my arse by far! & all it done to it was a cat back exhaust + pod filter & i got a full exhaust & pod filter.

2 be honest though, that gtir aint that crash hot. The car interior aint in the best condition, it a lucky dip with imports, you get some good ones & you got some sour ones & ive seen a few sour gtir

He had it for over 6months now & he purchased it for $22K i think it was & little steep i know. I wouldnt personally buy a 90-93 year old second hand car for that price, im sure you can import it & get it alot cheaper then the price my mate got it for.

I got my skyline for under $15k, once i reach $22k im sure my car will skin alive the gtir.

Joe.

The Gti-r is an awesome package, performance wise. They can look pretty tidy (nice one comes around near my work occasionally) but the fact it's a hatch and so small puts me off. That said, i would never bag, nor talk anyone out of buying one.

And if you're gunna buy a hot hatch...make sure it really is a hot hatch :uh-huh:

John at Unique Auto's at Castle Hill has one in Black at the moment. It was well under $22000. He took me for a quick spin last Saturday. Very ordinary interior,,,YUK!!! and don't talk to me about front end drift coming out of corners. That poor little car suffers from far to much weight in the front,,,what would make it worse is modding it,,, so you run a big fmic and doi away with the bonnet mounted one,,,which we all know doesn't work. That would add 25-30 more kilo's to the front,,,,Scary.

I was all for buying one before we got the Skyline,,,,I'm so glad we didn't.

Neil.

Guest lixid

i will wait until i got my power fc into my car and see how it goes

because i am a skilless driver so i think a 4wd will cover some of my weak points while driving. that's all. i didn't know that a gtir is a 4wd. and i thought it is very cheap. once i found out that gtir is a 4wd, with such performance, i suddenly had the thought.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...