Jump to content
SAU Community

Recommended Posts

Make me the third. Mine whines when coming off throttle or rolling in neutral. Fairly annoying, thought of just buying a second hand diff and housing and swapping it over. But then how do I know the next one wont do it too. From what I've been told they can whine if the gears dont mesh together properly. So if the gears are worn there is play in the diff, hence it whines when not accelerating. I've been thinking of trying a different oil. might help a little. Any thoughts????

i got the same problem. As the speed increases the whine gets louder. I got myself another diff for $300. Havnt put it in yet, but wen i get the time ill put it in, and hopefully all works out, and i refilled the new diff with penrite diff oil. I heard that aint bad either.

Rip the diff out, get the bearings replaced and the crown wheel/pinion checked and the clearance adjusted.

Done.

how much would that cost to get a mechanic to do it?

also how much do u think it would cost if i rip the diff and send it to the mechanic?

cheers

Most likley they will charge per hour.. Around 75 bucks an hour by most mechanics..

Maybe worthwhile if you bring your car into the shop and let them check it out and rip it apart..

Let them find the problem first, and then go from there.. Could be just a simple fix..

For a complete reco for the diff in my R31 skyline (bearings, seals, crownwheel and pinion) and removal and fitting was it was $950. I am kicking myself for not doing it.

It is actually quite a easy job to reco a diff if you have a basic knowledge of tools. The only special tool you need is a dial indicator to do the back lash and a oxy torch to heat the crownwheel up to put it on the diff centre. You will also need a torque wrench to test the limited slip diff. You will also need to mesh the diff properly, that info can be found in those gregories car manuals or on the internet.

yeah. ive got the same issue.

i thought id try to launch my gtr with a nismo tripple.

it didnt like it much. now it whines lol. not bad. but coz ive got a solid mounted subframe it makes the noise all that much more louder

so yeah. r200 diff reco.. how much??

taking the diff out isn't that hard. unbolt the drive shafts, unbolt the shaft coming from the gear box. and then there are two bolts at the front to remove, and i think 2 or 4 on the back. For $950 you could buy a 2-way, or 1.5-way.

for a gearbox shop to just have a look/listen they probably wouldn't charge you. but i spose different places may charge. anyone recommend a gearbox/diff shop? in brisbane

my 31 diff whined, as they do, especially after a number of skidpan days.

used synth fluid and some diff addative (lucas i think) from supercheap, and it was sweet.

addative is cheaper than a new diff. I had a 2nd hand reconditioned LSD centre put into my 31 for $500.

just keep a spare diff on hand.....

sorry for the stupid question

but would it still be alrite to use it at track days and stuff... coz its something i dont want to upgrade/repair yet until i decide what i want to do with it? rebuild it or go mechanical 1.5/2 way

  • 3 weeks later...
yeah. ive got the same issue.

i thought id try to launch my gtr with a nismo tripple.

it didnt like it much. now it whines lol. not bad. but coz ive got a solid mounted subframe it makes the noise all that much more louder

so yeah. r200 diff reco.. how much??

Dave

have u got a quote for it yet? if you did where abouts did u go?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...