Jump to content
SAU Community

polishing intake and manifold

dru32

By dru32,
in Exterior & Interior Styling

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

yes...comes up well... just be careful getting too down and dirty with an orbital sander as it can leave marks that are hard to sand and buff out by hand later..

I use a drill with orbital attachment .. you can get a buffer thing (sheepskin pad) which helps in the buffing process. "Autosol" in a tube works well (about $10 a tube i think).

i gotta do my intake plenum soon... that will be a bitch - but i've gotta do it of course :(

coco... hmmm..no idea about the wheels! Not sure how they would come up??? I think they are steel so probably won't come up great. You can only try..

Use course paper (thru orbital sander to save time).. then to really fine stuff by hand... Then stick some Autosol on there, and buff to shittery.. then wipe off the residue using cloth..then sand back a bit more..then do it again.. and after a long while it will look nice.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Help! Leak coming under transmission

      By GTSBoy · Posted

      So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
×
×
  • Create New...