Jump to content
SAU Community

Recommended Posts

are you guys sure the r33 thermo fan doesnt switch on with aircon? i thought it did. not constantly, but as needed.

Yes you are right, even R32 but i think we'd like to have the fan turn on a bit earlier than what set (factory temp set at 94degree i believe) by Nissan just to be on the secure side.

  • 1 month later...
  • 4 weeks later...
Thanks for the how to Cubes, worked a trick. But I think its a little too late for my compressor, I think the summer period has over cooked it. Oh well I have a replacement one here.

What gas are you running? Our compressors are not designed to deal with the high pressures experienced with R134a gas.

Find an aircon specialist that is licensed to deal with R12a; a MUCH better option.

I've had both gases in mine and the R12a is much better. I can no longer hear the a/c compressor roar, I can no longer feel when it clicks in and out and the power it sucks out of the motor is hardly noticable UNLIKE R134a.

R12a is a more efficient and environ friendly aircon gas than R134a.

Don't confuse R12a with R12. They are two different gases.

yeh i converted it to R134a gas and ever since then have been having probs. 2 weeks after I had it done it built up too much pressure and stopped working. They had to release some gas and it worked again for a few months then the compressor went. I'll have to get the compressor replaced and then fill it with the r12a then.

What gas are you running? Our compressors are not designed to deal with the high pressures experienced with R134a gas.

Find an aircon specialist that is licensed to deal with R12a; a MUCH better option.

I've had both gases in mine and the R12a is much better. I can no longer hear the a/c compressor roar, I can no longer feel when it clicks in and out and the power it sucks out of the motor is hardly noticable UNLIKE R134a.

R12a is a more efficient and environ friendly aircon gas than R134a.

Don't confuse R12a with R12. They are two different gases.

haha ive converted mine to R134a.

The power drain is huge, wouldnt dare turn it on whilst idling at lights :whistling: When coming to a stop, i always put it into neutral and rev a bit so it doesnt stall it self :P

haha ive converted mine to R134a.

The power drain is huge, wouldnt dare turn it on whilst idling at lights :whistling: When coming to a stop, i always put it into neutral and rev a bit so it doesnt stall it self :P

lol mine wasn't quite that bad but it made the car feel very very dull.

  • 7 months later...

i did this and it worked a treat,

also added another wire connecting it to the black side of the diode then ran the wire into my cabin with a switch that connects to ground, now i can turn it on via the switch or via the air con

Say ur radiator temp has rose a bit, just flip the switch and instantly the overheat fan will kick in and aid in cooling your radiator.

  • 3 weeks later...

has anyone tried this on an R33?

I'm about to replace my aircon fan, as mine is seized, and probably has been for some time. although the aircon is still quite good :blink:

now to work out how to get the fan out without removing the fmic :devil: . i tried, but it doesnt look possible, so i unplugged it for the time being.

Edited by Munkyb0y
  • 1 year later...

as hot weather has come around in victoria, this requires a bump up to the top :yes:

took my car to get an AC checkup and they told me to wire in the radiator fan startup.

One question, after turning off the AC is the rad fan still on? or does the wire+diode signal the rad fan to turn off?

  • 11 months later...

Yes, I would like to do this mod on my S2 R33 for this summer! Does anyone know if the fuse layout is the same as the R32's?

Also, does it actually make much difference to the air temps (inside the car) when you've just started the car and it's ultra hot outside, but you're sitting still? I'm finding that for the first few mins it never really cools down much inside if it's >35C outside and I'm not doing >40-50km/h. On the flip side, once I'm doing >40km/h would I really need this 2nd fan going whenever the A/C is on?

Oh, and what happens if the car reaches 91C but the A/C is off? Does the overheat fan stay off? Or, in other words, is the overheat fan now solely controlled by the A/C?

Edited by benro2

will be trying this mod its got 2 be 1 of the cheapest 1s out and it will give me a chance to check if my thermal fan works (i dont trust the 1 the panel beater fitted)

  • 4 weeks later...
took my car to get an AC checkup and they told me to wire in the radiator fan startup.

likewise - when i had my regas done the mechanic also advised running the thermo fan would knock off approx 5degrees from my current internal vent temp which is @ 11degrees

this is a fantastic mod, i'll do this today :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...