Jump to content
SAU Community

Recommended Posts

  • Replies 166
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I'm at the gabba - for those who don't know where we are goin I can meet at Milton Maccas prior and head Nth from there...

Note: Only suggestion at this stage - depending on replies obviously

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2881216
Share on other sites

I'm at the gabba - for those who don't know where we are goin I can meet at Milton Maccas prior and head Nth from there...

Note: Only suggestion at this stage - depending on replies obviously

i'm gonna be drivin up that ways, i can meet up

ian i'll have a meatlovers and a hawaiian

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2882066
Share on other sites

you know you want to :bomb_ie:

Ground rules have been added to the first post. The usual, dont be a dickhead rules. None of you should have to read them, if you think what your doing might require you to review the rules I ask you to look at the spirit of the rules and the cruise, not the letter.

Most importantly however is stay off peoples tails. Id like to see at least 1.5 seconds between each car, there will be alot of cars up there and alot of drivers that are unknowens, at least to me. Anyone found to be being a problem will be cautioned once, then they will be asked to go home. I dont want to see a repeat of the december run's bad apples. Stoned ute drivers and mad-skid 200's.... :sleep:

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2882200
Share on other sites

Ian,

what time are you likely to leave the Waterworks road BP?

I have to go to the hillclimb briefing on Friday night at 7pm - going to try the Mt Cotton hillclimb on Sunday.

Might all get to hard to come on the cruise, as I want to change my oil sometime between Friday night and Sunday morning (track day last Friday).

cheers

Mike

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2884363
Share on other sites

I can push it back a little if you would like, probably leave the BP at 7:30 - 7:45? there will be the usual stuffing around at the first meet up point, people will be late, etc etc. If you can get to the bp on waterworks road by 7:45 we will be there. If your running late just push it up nebo, by the sounds of things your pretty quick and the route has been posted, you could prob catch up by jollies.

Konrad, do what azzurra says :laugh:

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2884377
Share on other sites

For thoes of you who are going to be late:

Please ring me ON THE NIGHT and let me know, or SMS me ON THE NIGHT. We will be leaving once the last person rocks up or at 7:30 from the bunnings, then 7:45 from the BP. After that your next chance of catching us is at jollies... There are few stops after jollies for a while, but if you dont get to us then make sure you have a coppy of my dodgy-directions.

My number is 0400 813 419

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2885760
Share on other sites

Nah i've gotta leave straight after work at 4pm so i'll be passing thru maryborough about the same time as that pizza is passin thru your systems lol :laugh:

Wish i could go tho :( i want to see pics when i get back!

Link to comment
https://www.sau.com.au/forums/topic/153441-closed/page/6/#findComment-2885848
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...