Jump to content
SAU Community

Recommended Posts

Hi everyone,

Im long time reader, first time writer.

I have a big problem with my Skylines Brakes :sleep:

It seems as if the brake shoes are wedged into the Disk rotor and i cant get it out.

I've tried using the two bolts to remove the rotor, but it pulls the entire hand brake assembly out with it as well. Would anyone know how i can readjust the hand brake so that i can remove the rotor.

I'm afraid if i try remove it any further using the bolts, ill rip the entire hand brake off n needa buy a whole new assembly which = more money :bomb_ie:

I've also heard you can adust the handbrake from the plastic cover on the rotor, but i cant seem to understand how to adjust it. Do you push it in or do you turn it with a long nose plier? It cant be adjusted with a screwdriver as the face is flat.

And yes, i've released the handbrakes when i tried removing the brakes. I also tried whackin it with a hammer but the top of the rotor wouldnt even budge! The handbrakes seem wedged into the rotor.

Is there a secondary backup adjustment that i can do to loosen the brakes b4 removing the rotor?

Please help someone!!

My skylines currently doin 15L/100km with feather like acceleration.

Thats to high for this car =(

Thanks EveryONE!!

=D

Link to comment
https://www.sau.com.au/forums/topic/154995-how-to-remove-disk-rotor/
Share on other sites

The shoes are adjusted through the 1/2" hole in the rotor hat. The adjustment is near the "7 o'clock" position. You will need a flat-blade screwdriver to undo the adjusting wheel.

But how do you undo the adjusting wheel if theres nowhere 2 wedge the wheel fingy. Inside is just a plain round metal thing. The only thing i can fink of is using a long nose plier 2 twist and readjust.

Has anyone had this problem before?

The shoes being wedged stuck to the rotor so that you cant remove it wifout adjusting the handbrakes?

Ill try it when i get the chance.

Cheers

Back off the handbrake adjustment in the cabin, and then disconnect the cable at the balance bar which sits infront and above the diff housing.

You may just have too much tension on the handbrake so its holding the pads on.

hmm we need a pic of the hole....there is an adjuster in there somewhere....back it off from the cabin as much as you can first though (small nut on the handbrake cable at the lever).

The handbrake is off isn't it?

hmm we need a pic of the hole....there is an adjuster in there somewhere....back it off from the cabin as much as you can first though (small nut on the handbrake cable at the lever).

The handbrake is off isn't it?

Yes the handbrake is off. LOLZ and its lowered 2 d max already.

Still handbrake wedged in rotor. Still cant get the adjustment 2 work, l mite try release the centre adustment as well.

Thanks everyone

Yes the handbrake is off. LOLZ and its lowered 2 d max already.

Still handbrake wedged in rotor. Still cant get the adjustment 2 work, l mite try release the centre adustment as well.

Thanks everyone

you may have lips on the inside of the rotor, making it hard for the lips to go over the hand brake shoes, if this is the case you gotta get em off any way you can and remove lips or replace rotors, thats if you REALLY need to get em off :no:

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...