Jump to content
SAU Community

Recommended Posts

Yes that is a pig of a hose.

you will need a long set of needle nose pliers to get the clamp off and then spray a tiny squirt of wd40 inside and outside the hose and twist. it will come off.

getting it back on is another story...

yeah, there's no easy way out. You need tiny hands. Try and undo the clamp anyway you can.

Either a long screw driver if you can, or needle nose pliers.

I cut an 8 mm spanner in half and got my hand in (I lubed it up with soap and got it in - yes i was scared i'd never get it back out)

once you get the clamp undone enough, you can get the line out, by pulling the line itself from outside

If you're installing the hks turbo and replacing the line with a braided one, I have no idea how on earth you'll get the new line in.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Been there, done that. Not fun.

Having 2 people to remove it helps, one holds the hose and the other yanks on the metal line.

For install of braided lines atleast you can bend the rubber hose up and fit the barbed end of the braided line, then feed the other end of the line back around the back of the head.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Just hacksaw the metal pipe off, probably as close to the turbo as possible????

I guess I'm worried about metal filing getting in there and also, there would be no lip to stop the pipe coming off..(or would that not be a problem ? )

Have a go ya mug!!!

Actually to tell the truth, mine was held on with the hose clamps that you pinch together with a set of long handled pointy pliers [$10 at Crazy Joes or Micks or somesuch]. The hose was a bit stuck, so I used a long thin screwdriver to work under between the hose and the metal pipe and some WD40 and it came out easy. Don't ask me how to put it back on, I haven't got that far yet..........lol.

PS I don't have a valley cover. that probably made it easier. Actually I found the bolts that screw into the block that hold the stays on this hose harder to get off than the hose.

metal filings are not really an issue wiht that particular hose. That is just a coolant hose, so ti's just the cooling system - just water.

Ther'ell be plentny of shit in there anyways, like everytime I dropped the coolant in my daily driver (not my skyline), there's all rust, and crap that comes out.

Don't get metal in the oil lines though. Totally different story

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

Also, I'd replace that rubber hose at the back. Someone recently, forgot who it was had the hose blow (they're' 10 years old afterall). Better do it now while the turbo is off. Imagine if it blows in 6 months time and having to do it with the turbo on!

If you cut the line, keep in mind that the cooling system is under pressure (up to 0.8bar). Without a bead around the line, the hose can possibly blow off. Imagine having the line blow off on a hot day as you're driving along the freeway. bye bye engine

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

that is wat i did when i replace my turbo with a HKS turbo. and the hks turbo came with a braided line. so i cut it just before the bent.

basicly the same as "Ol_Mate" did!

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

Photos would be great !

So you didn;t need a lip on the end of the pipe with that gland thing?

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Do it right, do it once :happy:

You can do it. Motivational thread for jase. go jase go jase go jase :)

Edited by MANWHORE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...