Jump to content
SAU Community

Recommended Posts

Originally posted by Sumo

Holden tell people to drive off as soon as they start the car with their new ones. They believe that it only consumes fuel and the motor warms up better if u just take it easy driving for a few kms.

Sumo

yeah but would you trust someone who makes a commodore?

i believe at the bare minimum a minute or so to give time for the oil to get around the engine. i usually give it 3 - 5 mins and then drive easy 'till the gearbox warms up too.

to me it doesn't seem like much if it will help at all to reduce wear.

Waz.

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-323356
Share on other sites

Holden tell people to drive off as soon as they start the car with their new ones. They believe that it only consumes fuel and the motor warms up better if u just take it easy driving for a few kms.

Holden are more conserned with percieved fuel economy of their cars-they dont want you to waiste fuel idling in the driveway,and then tell everyone that Holden has crappy fuel economy.

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-323388
Share on other sites

I kick it over, get settled, and proceed to tackle the carport / driveway. By then, the oil should have gotten around enough and I just take it easy until it's reached operational temps. It's useless to let your car idle for 10 minutes and then proceed to give it stick, because as RedlineGTR said, you still need to warm your gearbox and diff.

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-323581
Share on other sites

well i takes my car about 4 to 5 min tops for the temp guage to get to the right spot and thats wheni take off i dont give it alot of rpm proberly no more than 3 for a few min and then i prob go ujust a little over i dont rev my car much just got it worried ill hurt the baby =)

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-323600
Share on other sites

Guest Boxhead

meh i dont like to let engine warm up, i figure if im gonna stay low with rpms to let gearbox etc warm up, the engine will warm up in same time...

that b eing said, i switch on car, then usually change cd in stereo, get settled. close garage door and reverse out driveway so about 30secs give or take idle before driving, i wont boost till engine and oil temps are at appropriate levels

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-323631
Share on other sites

I start mine, let it idle for a few seconds so that the oil has a chance to circulate through the engine and then put the clutch in and select 2nd, let the handbrake off (since I'm on a downhill slope) and then ease it into gear and drive off sedately (:D

I don't have the time to start a car and then sit around playing with my stereo for 5 minutes, and driving it gently warms it up faster anyway.

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-324331
Share on other sites

Hey so have any of u guys got remote start at all? Hell yeah everyone needs to idle or drive slowly to let the water and oil warm up, but I would like the idea of remote starting the car knowing that I would be going out in a sec, and then jumping in the car and then taking it easy for less time before it is completely warmed up.... before BOOOSTING

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-324627
Share on other sites

i start mine, let idle for about 15 sec, reverse out driveway, then take it easy (under 3000rpm) with low load (driving off boost) as much as possible, until about a good 10km of driving, then gradually drive it harder if desired :P

even audi's manual for my dads S4 twin turbo states that u should not warm it up before driving, but instead drive softly on the move until operating temps are up (they got oil temp gauge) unlike our cars which have oil press. the diff and gearbox do need to be warmed by driving not idling.

Link to comment
https://www.sau.com.au/forums/topic/15798-warming-car-up/#findComment-324702
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...