Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

i drove my mate's 1995 model 180sx the other day with blactop sr20 which is the same engine used in the s14s aswell. it had catback exhaust and pod. honestly, straight line speed wise it felt alot like my parents' VT 3.8 v6. definately not as quick as i thought it would be.....i haven't driven a r32 so can't say which would be quicker...

factory times say both do around 15secs for 1/4 but keep in mind the r32 is a few years older than the s14s. personaly the series2 s14 has one of my favourite front ends, very mean lookin. but the rest of the car is average. and i hate sr20s.

RB20 engine/exhaust note has to be one of the sweetest sounding ever

Edited by R-SPEC

A common misconception is that the blacktop SR20s are all the same. You can basically say that the S13/180SX motors are the same with different cam cover colours.

The S14 (and S15 motors) are different to the S13/180SX motors. Among other things, the S14/S15 motors have -

-Variable Inlet Camshaft Timing (NVCS)

-Larger turbocharger (T28 vs T25G)

-Different inlet manifold setup. (Low port vs High Port)

S15 motors are slightly different again but is of little overall significance.

Cheers :(

stupid question.. this is the type of question that should come from boostcrusing..

sigh.. well basically the S14 is superior, lighter more usable.

180sx S13 red and black are near the same. the S14 and S15 use 28 turbos and have VCT. and high port inlet.

not all s14's have variable cam timing. only the late series 2. you can tell by the lump on the rocker cover.

All S14s have variable cam timing as well as the points i mentioned earlier. How do I know? Because I own both. :(:huh:

but stock they are both slow the s14 and the r32

My r32 when i bought it was stock except for a 3" exhaust but only from the cat back... This exhaust was one of the worst I have ever seen, terrible drone and if anything was causing a loss in power, when i changed it down the track I noticed the difference straight away!

Anyway, with that sh!tter of an exhaust I g'teched my car and ran 0-100km/h in 6.5 seconds. I personally dont consider that slow... but its all in perspective i guess.

My r32 when i bought it was stock except for a 3" exhaust but only from the cat back... This exhaust was one of the worst I have ever seen, terrible drone and if anything was causing a loss in power, when i changed it down the track I noticed the difference straight away!

Anyway, with that sh!tter of an exhaust I g'teched my car and ran 0-100km/h in 6.5 seconds. I personally dont consider that slow... but its all in perspective i guess.

but its not fast

Regardless.... YEARS ago back before SAU was born (2001/2002) I was on SDU. One bloke managed a best of 14.2 1/4 mile out of a dead stock R32 with a good launch and some wide tyres. So not really stock as it wasn't running its stock 205/55/16's :unsure:

---------

lmao... @ 11ty billion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...