Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Should have a petrol resistant foam rubber sleeve and hose clamp/s to mount it. I've not seen ANY shop including autosparkies that wire things up neat. Kindergarten kids could usually do better!!

They usually use the biggest soldering iron they can find, two rolls of dodgey insulation tape per job, have five twist joins in a 500mm length of wire, and crimp all connectors with a hammer or sidecutters.

LOL f*kn hacks!

What they figure is... if you don't see it.. it wont hurt you...

WRONG MUDAf*kRS!!!

They should take a crash course in how to unf**kthemselves.

OK OK, XXX did it. I spose its not bad to say it because i am sharing information that could be useful, as someone said if they cant see it it wont hurt them (the customer) or something along those lines. thats why i was so eager to get back in the tank and see what they really done.

First and last time to go there, wasnt happy with the service from the start.... i made an appointment at 10am and didnt leave until about 2.45.... but i spose workshops can be like that

i payed $120 for the install only... the pump was supplied by myself.

mods if u think this thread is not within guidelines than feel free to edit.

on a good note i got my FMIC installed today, happy with that and the guy who installed it

**edited by mods - please don't mention names**

I have a similar problem last workshop I left my car to gave me the car with

1 dint in the front passenger panel..denied by them.

1 window seal badly notched "drivers side"

1 side skirt chipped"drivers side"

I need to install cams/afms and retune.

I am not giving it back to these guys.

There work was good but are rough as guts on your car.

PM ME IF YOU WANT TO KNOW WHO THEY ARE IN MELBOURNE.

Probably best course of action if it hasnt been too long would be to sit down and consult with them, and maybe work out some appropriate resolution. but then again its upto how you would proceed in this circumstance. There are many and many dodgey work places, and very few that actually know what the hell they are doing with our cars and even less that will take the time, effort and care with out cars on anything mechanical. Hence why so many people do things themselves. Well one of the many things why anyway.

Noo good even still atleast you got to it sooner than later

it has been over a month since i done it, for the matter of 120 dollars i cant be bothered going back especially since they cant see it while it was installed. they will most porbably make excuses etc etc and highly doubt i will get my money back and i dont think there is anything else they can do for me.. i will just not go back there again

how much diff is the GTR pump over the stock? i would think the GTR would be easier to install than a walbro (aftermarket), I would think the GTR would use the stock mounting brackets etc. pm me the reply with the name of the workshop too. please thanks :)

walbro comes in a kit form and is so easy to install, it has a new hose with clamps, rubber mount down the bottom and pickup filter thing. also has a wiring harness with it. The hardest part is cutting the + and - and crimping/soldering them to the new harness LOL.

GTR pump uses everything the same so u dont need new hoses etc but it is slightly different on the bottom and wont sit in the cradle with the GTST rubber mount so this is where it gets ugly. If u a suitable piece of rubber and half a brain u could make a similar mount but yeah it help to have everything there when ur tank is opened up and u have no car to get bits and pieces lol

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...