Jump to content
SAU Community

Recommended Posts

Most of it seems OK except rear camber. You need to even it up a bit more. Bit more castor wouldn't hurt and you probably want to even up the front camber. All the bushes can be bought from the Whiteline/Bilstein groupbuy.

I would probably run 0 toe on the front though. Wheel aligners set it up like that for tyre wear to offset the camber.

Here's the link to the groupbuy and SKs recommended wheel alignment settings

http://www.skylinesaustralia.com/forums/in...showtopic=85467

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/159191-wheel-alignment/#findComment-2954425
Share on other sites

basically they gave you some front toe out (good thing) and the rear toe was f**ked before, but they have fixed it now. I would have preffered rear toe to be 0.00 and 0.00 but it's not too bad as is. I assume front camber is non-adjustable rear camber IS adjustable standard so they should have tried to even up the rear camber, even if it meant running 50 mins on the right to match the left, it's not bid deal. The front toe was also a bit out to start with, but it's good now. should feel quite nice.

I don't agree with what salad said about toe out being to save tire wear. if anything toe out increases tire wear, but it's great for steering response.

Link to comment
https://www.sau.com.au/forums/topic/159191-wheel-alignment/#findComment-2954457
Share on other sites

well the machine I used on saturday shows + as toe OUT.

but it would make sense in this case, as if it is toe out then it's a pretty 'racy' alignment and it will want to steer itself all over the road.

Link to comment
https://www.sau.com.au/forums/topic/159191-wheel-alignment/#findComment-2956127
Share on other sites

Hmm, odd, I've never seen a machine that has +ve as toe out, always toe in, but my experience is fairly limited, only used 2 machines before.

But yeah, it is unlikely that the run of the mill tyre store will set a car up with toe out (unless requested), always have toe in to offset camber wear. Those toe numbers look very typical and look a lot like what the wheel aligner at my work does (and why I dont listen to his suggestions of how to wheel align my car for track work)

Link to comment
https://www.sau.com.au/forums/topic/159191-wheel-alignment/#findComment-2956328
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...