Jump to content
SAU Community

Custom Afm

Dj laBBy

By Dj laBBy,
in Fabrication

 Share

Recommended Posts

Dj laBBy Collaborator

Dj laBBy

Posted
Posted

Hey anyone made a custom AFM??

Am thinking of using a Q45 (90mm 3.5") internals and plumbing it into a 4"pipe.

The reason you might say, to slow the air speed through the meter which will give a greater scope. Undoubtly 4" is not much of an increase, but i can also bolt it straight to the 4" turbo inlet and use a 4" filter. I was maxed out at 20psi (260rwkw) so maybe this may help a little.

Plus it is custom and i like tinkering. hehehe

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/
Share on other sites
Dj laBBy Collaborator

Dj laBBy

Posted
  • Author
Posted
your telling me you maxed out a q45 afm at 20psi and only made 260rwkw that doesnt sound right.. more info please

Ah good question.

Had low comp pistons and rb25 head, =extra low comp setup. It was somwhere around the low 7's cr.

When you think about it, 20psi is great for an AFM on rb30 setup, but it was the comp that was killing me, saying that it was an ignition monster, just wanted more and more. Could've thrown 30psi in there and it would've been happy.

However i have high comp standard rb30 pistons in there now so comp is a little more respectful, though would love to make over 300rwkw. So we just see.

Mate its a good experiment just to see how it all goes. plus "Custom" love custom!!!

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-2983997
Share on other sites
djr81 Grand Master

djr81

Posted
Posted
Hey anyone made a custom AFM??

Am thinking of using a Q45 (90mm 3.5") internals and plumbing it into a 4"pipe.

The reason you might say, to slow the air speed through the meter which will give a greater scope. Undoubtly 4" is not much of an increase, but i can also bolt it straight to the 4" turbo inlet and use a 4" filter. I was maxed out at 20psi (260rwkw) so maybe this may help a little.

Plus it is custom and i like tinkering. hehehe

My understanding is that if you change the internal diameter of the pipe in which the air flow meter resides you change the calibration of the meter.

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-2984524
Share on other sites
Craved Grand Master

Craved

Posted
Posted
My understanding is that if you change the internal diameter of the pipe in which the air flow meter resides you change the calibration of the meter.

thats more than likely trua and something that has already been discussed in the Forced induction section.

the modifictaion to the AFM would require you to create a boxed section one the side of the inlet pipe and im assuming that it would require it to be on a straight section too to ensure the flow is even through the meter.

be some fiddly work to get the mounting threads welded on to keep the unit flat inside your box.

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-2984602
Share on other sites
Dj laBBy Collaborator

Dj laBBy

Posted
  • Author
Posted

Yah calibrated, true, but basically whats the difference in calibration when you tune the car for the new calibration?? Yah am running a Power FC, so its all good. The only time you'd be worried about "calibration" so to speak is when you are using the standard comp.

Basically this way you are kinda tricking (real lamens terms) the computer there is less air going through the AFM, the just adjust the mixtures to suit, not rocket science.

Yah tricky making a box?? well really all you need to do is to get a bit of pipe, machine or file a basic flat, make a base plate, weld that on, then by cutting some ally plate say 20mmhigh x what ever the standard width is, then just weld it all up. Screw the AFM unit in and just silicon on a top if you can't be bothered tapping and screwing the top.

Piece of piss(if your a welder/fabricator)

Was thinking of it last night in bed for about an hour. Should hopefully have started it and maybe some pics by monday.

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-2985319
Share on other sites
Craved Grand Master

Craved

Posted
Posted
Yah calibrated, true, but basically whats the difference in calibration when you tune the car for the new calibration?? Yah am running a Power FC, so its all good. The only time you'd be worried about "calibration" so to speak is when you are using the standard comp.

Basically this way you are kinda tricking (real lamens terms) the computer there is less air going through the AFM, the just adjust the mixtures to suit, not rocket science.

Yah tricky making a box?? well really all you need to do is to get a bit of pipe, machine or file a basic flat, make a base plate, weld that on, then by cutting some ally plate say 20mmhigh x what ever the standard width is, then just weld it all up. Screw the AFM unit in and just silicon on a top if you can't be bothered tapping and screwing the top.

Piece of piss(if your a welder/fabricator)

Was thinking of it last night in bed for about an hour. Should hopefully have started it and maybe some pics by monday.

only reason if that would be tricky is if the underside of the circuit board isnt flat

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-2985336
Share on other sites
  • 2 months later...
Medium Dave Proficient

Medium Dave

Posted
Posted
Yah calibrated, true, but basically whats the difference in calibration when you tune the car for the new calibration?? Yah am running a Power FC, so its all good. The only time you'd be worried about "calibration" so to speak is when you are using the standard comp.

Basically this way you are kinda tricking (real lamens terms) the computer there is less air going through the AFM, the just adjust the mixtures to suit, not rocket science.

Yah tricky making a box?? well really all you need to do is to get a bit of pipe, machine or file a basic flat, make a base plate, weld that on, then by cutting some ally plate say 20mmhigh x what ever the standard width is, then just weld it all up. Screw the AFM unit in and just silicon on a top if you can't be bothered tapping and screwing the top.

Piece of piss(if your a welder/fabricator)

Was thinking of it last night in bed for about an hour. Should hopefully have started it and maybe some pics by monday.

Might be a bit of science in it, the afm reads the airflow and outputs in a logarithmic curve, then the computer outputs that in a linear curve using a conversion table, by increasing the diameter you may throw the curve well out of whack. How's it all going anyway? im curious to know

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-3135213
Share on other sites
  • 3 weeks later...
  • 3 weeks later...
Craved Grand Master

Craved

Posted
Posted

Hi, I don't know much about air flow meters but i need one for my 95 series 2 gtst skyline.

Can anyone advise me on what one to get and where to get it from?

Cheers.

You will get a better response in the Forced Induction section.

stick with STD or if you have a Power FC and are chasing power try a Z32..

Search in FI if you are unsure about this

Link to comment
https://www.sau.com.au/forums/topic/160559-custom-afm/#findComment-3203032
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...