Jump to content
SAU Community

Recommended Posts

took apart the carbi in a crapbox that i've been using.

mate lost a circlip for a throttle linkage. i lost whatever holds the other throttle linkage

so i just got some paper clips, bent them around to replace clips :cheers:

still running fine ha

one day it'll either not accelerate or jam open ;)

  • Replies 133
  • Created
  • Last Reply

Top Posters In This Topic

a guy i know has a gemini and he knows when to top up the oil by hom long the oil light stays on for when he stops at an intersection. when it stays on for longer than a certain number of seconds it needs topping up.

lol thats a good one. I have dodged up so much on my daily driver. The throttle body on the carby is so worn out that it wouldn't close properly and always idled high depending on if the butter fly jammed or not. So just added an extra return spring onto it to help pull it back close properly.

I when i need new brake pads on the rear drums i just look thru a box of spares that i have and find some old ones that have good meat left on them. seems to wear the leading pad out faster so i just get a whole bunch of rear pads that i find and put them on. The leading and trailing pad seem to be the same so interchangable. saves few $$.

When i bust a CV boot cover thats no sweet. I just get some plasitc bag and wrap that around it and duct tape that sh!t on. last for longer than u would think.

Radiator is always getting holes in it. but i just dodge up that with some metal mend putty. It now seems to have more putty on it than metal lol.

The structural support for the sills under the car are a little rusted out and make it hard to lift the car there :). Had to get a RWC for the car so just bogged the rusted out area up and shapped it to look like the original chassis. then painted it with body deadner and when dry i just mixed up some nice mud and splatted that all around under the car to hide all. Didn't bother washing it for the assesors.

The rubber steering joinner on the steering shaft wouldnt pass RWC cos it had some small cracking in it, so i just rubbed grease into the crack to hide it and they didnt notice.

Reverse light switch in gear box buggered up so i wired the factory wiring to a switch in the car now so i have to flick a switch now to turn reverse lights on.

Brake calipers where shaking around all the time on the pads and rotor because the securing pins where worn. So just wrapped the pins with aluminum flashing (stuff u use on a house) and shoved it back in.

Hmm did a few other things. will add them as i remember.

lol thats a good one. I have dodged up so much on my daily driver. The throttle body on the carby is so worn out that it wouldn't close properly and always idled high depending on if the butter fly jammed or not. So just added an extra return spring onto it to help pull it back close properly.

I when i need new brake pads on the rear drums i just look thru a box of spares that i have and find some old ones that have good meat left on them. seems to wear the leading pad out faster so i just get a whole bunch of rear pads that i find and put them on. The leading and trailing pad seem to be the same so interchangable. saves few $$.

When i bust a CV boot cover thats no sweet. I just get some plasitc bag and wrap that around it and duct tape that sh!t on. last for longer than u would think.

Radiator is always getting holes in it. but i just dodge up that with some metal mend putty. It now seems to have more putty on it than metal lol.

The structural support for the sills under the car are a little rusted out and make it hard to lift the car there ;). Had to get a RWC for the car so just bogged the rusted out area up and shapped it to look like the original chassis. then painted it with body deadner and when dry i just mixed up some nice mud and splatted that all around under the car to hide all. Didn't bother washing it for the assesors.

The rubber steering joinner on the steering shaft wouldnt pass RWC cos it had some small cracking in it, so i just rubbed grease into the crack to hide it and they didnt notice.

Reverse light switch in gear box buggered up so i wired the factory wiring to a switch in the car now so i have to flick a switch now to turn reverse lights on.

Brake calipers where shaking around all the time on the pads and rotor because the securing pins where worn. So just wrapped the pins with aluminum flashing (stuff u use on a house) and shoved it back in.

Hmm did a few other things. will add them as i remember.

does this guy win dodgyness of the year award? i think so!

this thread is a classic

Got defected in my old nissan NXR for height of 70 mm. got it to 110mm by jacking it up and jamming about 20 blocks of rubber in between each spring coil and had no travel at all. too scared to drive it and was for sale anyway. sold it the next week and the lady drove it home from my house in Newcastle to VICTORIA with 80 rubber blocks jammed in the springs. couldnt stop laughing. hope she made it home ok

lol thats a good one. I have dodged up so much on my daily driver. The throttle body on the carby is so worn out that it wouldn't close properly and always idled high depending on if the butter fly jammed or not. So just added an extra return spring onto it to help pull it back close properly.

I when i need new brake pads on the rear drums i just look thru a box of spares that i have and find some old ones that have good meat left on them. seems to wear the leading pad out faster so i just get a whole bunch of rear pads that i find and put them on. The leading and trailing pad seem to be the same so interchangable. saves few $$.

When i bust a CV boot cover thats no sweet. I just get some plasitc bag and wrap that around it and duct tape that sh!t on. last for longer than u would think.

Radiator is always getting holes in it. but i just dodge up that with some metal mend putty. It now seems to have more putty on it than metal lol.

The structural support for the sills under the car are a little rusted out and make it hard to lift the car there :closedeyes:. Had to get a RWC for the car so just bogged the rusted out area up and shapped it to look like the original chassis. then painted it with body deadner and when dry i just mixed up some nice mud and splatted that all around under the car to hide all. Didn't bother washing it for the assesors.

The rubber steering joinner on the steering shaft wouldnt pass RWC cos it had some small cracking in it, so i just rubbed grease into the crack to hide it and they didnt notice.

Reverse light switch in gear box buggered up so i wired the factory wiring to a switch in the car now so i have to flick a switch now to turn reverse lights on.

Brake calipers where shaking around all the time on the pads and rotor because the securing pins where worn. So just wrapped the pins with aluminum flashing (stuff u use on a house) and shoved it back in.

Hmm did a few other things. will add them as i remember.

Thanks guys. I do try. lol.

We all know who the man is around here!!

Your a legend love it!! I thought I was dodgey with my corolla but you by far take the cake!! much respect!

tie rod ends held on by 3 thread turns for a 8 hour track day

well, the minimum requirements for fitting is 2 thread turns - and that is for pressure fittings

as longs as its lock-tited on alright....

another dodgy thing iv done, thought id do a lil bush mechanic short shifter which consisted of a hack saw, cut it nice and short then found a small shift knob,

it was too big for the shifter so i got a bolt and super glued it inside the shifter and then put the threaded end of the long bolt into the hole in the shifter, threads on the bolt were too skinny so i just filled up the shifter hole with super glue lol, its nice and STUCK in there now

god knows how im gonna get it off :P

me and my mates have done:

- power right mirror works only when a cable tie is used to adjust angle of bunch of cables going through grommet.

- driving around for 4 months without rear seats

- using bandaids to hide rust spots

- running 4 speakers from a 2 channel amp, 2 speakers eventuallly blew

- attaching side skirts and rear pods to hide accident damage and rust, then sold the car

- driving with no transmission oil, no service ever, it lasted for a year and many burnouts. Got $160 scrap metal, cost $200.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have a vb in honour of the car comming back
    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
×
×
  • Create New...