Jump to content
SAU Community

Recommended Posts

I am stripping a 1992 2 door R32 GTS-T, All parts available too many to list let me know what you are looking for and I will give you a price, and I can supply pictures.

R32 seats rear $30.

R32 steering wheel $60.

FMIC $60

Doors $90 each

Factory wheels $200

boot trims $100 pair.

headlights I have 2 sets normal $150 pair and projector $250 pair

front guards 2 pairs 1 set $140 black and one perfect grey set $240.

I have all parts needed to repair a front smashed R32 GTS-T, looking to sell as a package 2 headlights 2 indicators 2 guards , bonnet, front bar, nose cut $999.

instrument cluster $80 120,000kms and I have one with 30,000kms for $110.

+ many more parts please pm me.

Thank you.

Edited by sky88
Link to comment
https://www.sau.com.au/forums/topic/163011-stripping-r32-gts-t/
Share on other sites

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

oh, and in keeping with the forum rules please at least list some of the parts you have, and the prices you are asking for them. thanks.

urgently need airbox. price?

im looking for drivers elec window controlls, or possibly just the passenger window switch that is on the drivers side,

i cant put the passenger window up form the drivers side, hope that makes sense?

im looking for drivers elec window controlls, or possibly just the passenger window switch that is on the drivers side,

i cant put the passenger window up form the drivers side, hope that makes sense?

i am also interested int the drivers window switch

and the small air vent on drivers side :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...