Jump to content
SAU Community

Recommended Posts

Hey guys,

This probably sounds stupid but how exactly tell the difference between a series one and series two R33 just by looking at it. And is there a difference in performance between the two?

Thanks,

Sammy.

Link to comment
https://www.sau.com.au/forums/topic/163075-how-to-tell-if-r33-is-s1-or-s2/
Share on other sites

Hey guys,

This probably sounds stupid but how exactly tell the difference between a series one and series two R33 just by looking at it. And is there a difference in performance between the two?

Thanks,

Sammy.

A series 2 from the front the Bonnet/ Grill is different, The headlights are a different shape and the front bar has those round fog lights and indicators in it. A series one has that funny grill with emblem on it and less angualr lights

From the rear the series one has that low rounded wing whereas the series 2 has a higher squared off wing

No difference in performance

PS prepare for heaps of people to tell you to search

There is little or no difference in performance between S1 and S2 (other than the wear and tear resulting from the fact that S1's have typically seen a few more years of service).

From memory, these are the main differences...

Interior:

Updated trim

Updated instrument panel

Passenger airbag

Exterior:

Round indicators and foglights

Sharper bonnet lines, grill and headlights

Chrome backing on headlights

Chrome 'S' Skyline symbol on bonnet

Color coded 'Skyline' trim under boot

Titanium coloured boot lock

Squarish rear spoiler

Mechanical:

Updated ECU

Nylon intake wheel on turbo

Updated ignition system

Different CAS for post Sept 97 models

There is a thread somewhere on the forum which has a detailed list of all the differences between S1 and S2 - do a search.

post up the interrior pic, pic of the gear shiift surroud and the dash surround

i think series 1 have the coin slot on the dash

series 2 have the coin slot on the gear shift surround

at least I think thats how it goes

you dont have a S2 unfortunatly, its a S1/.5

S2 are 96-98 models S1 are 93-95

Ummm no. u are wrong... very wrong, mine is a 95 series 2.. November build...

stick that up there.:)

OK so what series is this one...?

Yrs is a so called 1.5 dude

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...