Jump to content
SAU Community

Recommended Posts

thanks for that.

Want to get a couple of quotes to see if its worth rebuilding r32 box or put in a r33 box.

- Patrick

not worth it just drop in the 33 box. s2 if possible.

HAHAHA ! HAAAA ! ! Try getting one ! ! well, they're out there: $1750 from the ONLY wreckers in Melbourne Who've got one, $1400->1700 privately, if You don't mind pot-luck . . . . (That's not a shot at anyone, just the nature of 2nd hand stuff)

Got a quote from All Wheel Drive Gearbox Reconditioners;

-------------------------------------------------

- Remove & Replace gearbox - $400

- Bearings and seals - $1200

Strip clean and inspect gearbox

Remove and replace bearings and seals

Re-assemble

Any Required parts (syncro etc) no labour incurred

Syncro's (if needed) are $500~ from Nissan, so looking at $2100 total?

-------------------------------------------------

Will drop by 360gearbox tomorrow and see what they have to say...

If i get a r33 gearbox for $1500, how much it cost to put into car driveaway?

$400 to remove/fit + extra's to make it actually work? ~ $2000 total?

Cheers

Patrick

Got a quote from All Wheel Drive Gearbox Reconditioners;

-------------------------------------------------

- Remove & Replace gearbox - $400

- Bearings and seals - $1200

Strip clean and inspect gearbox

Remove and replace bearings and seals

Re-assemble

Any Required parts (syncro etc) no labour incurred

Syncro's (if needed) are $500~ from Nissan, so looking at $2100 total?

-------------------------------------------------

Will drop by 360gearbox tomorrow and see what they have to say...

If i get a r33 gearbox for $1500, how much it cost to put into car driveaway?

$400 to remove/fit + extra's to make it actually work? ~ $2000 total?

Cheers

Patrick

$400 is too much just to remove & replace! $250 will cover it easy. Either that or they have no experience with skylines.

Thanks for the link wes81!

Interloper, they have a big sign on their workshop saying they specialize in GTR, WRX and all Japanese vehicles lol. Only saw 4WD's though..only went to them for a quote+free drive test. Might give them a miss as they didnt seem dedicated to japanese cars. I guess they needed to fill a blank wall on their workshop with some writing :happy:

HAHAHA ! HAAAA ! ! Try getting one ! ! well, they're out there: $1750 from the ONLY wreckers in Melbourne Who've got one, $1400->1700 privately, if You don't mind pot-luck . . . . (That's not a shot at anyone, just the nature of 2nd hand stuff)

not that hard if you know the right people, i picked up one for 1500

Interloper, they have a big sign on their workshop saying they specialize in GTR, WRX and all Japanese vehicles lol. Only saw 4WD's though..only went to them for a quote+free drive test. Might give them a miss as they didnt seem dedicated to japanese cars. I guess they needed to fill a blank wall on their workshop with some writing :)

lol, well there you go - instant cred with a sign like that :)

doesn't actually mean anything really.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
×
×
  • Create New...