Jump to content
SAU Community

Recommended Posts

**I would've posted this in the Next Skyline section but I thought it was too special.

At the New York Show it was revealed that a V36 Skyline Coupe Convertable is on the cards for a 2009 release, at the very least as an Infiniti in the US, with a domestic Japan release as yet undecided. Not since the Prince Skyline Sports of 1961 has there been a Skyline Convertable of any sort:

gallery_4816_8_14487.jpg

gallery_4816_41_373609.jpg

Yes it's just CG but it gives a good idea of what to expect.

The convertable will obviously be based on the V36 Skyline Coupe, but with updated running gear as the Series II V36 will be scheduled for sale by then. One other ineteresting thing is the engine, a VQ37*VHR* from the Coupe, with a new VVEL 'electric motor driven camshaft switching' valvegear... more on this later when I get a chance to fully translate the article. The new engine is more efficient, produce less emissions, still have the high response of the current VQ35HR, and have higher capacity and torque to boot. I don't know, but this seems like the last hurrah of the conventional petrol engine for some reason...? Theres ALOT of technology going into it and theres not a turbocharger in sight... more later.

*Edit: The VQ37VHR is even more environmentally friendly than the current engine, but with even more response and torque right throughout the rev range. Reduced 'pumping loss' and reduced total exhaust emissions, with CO2 reduced by 10% aswell make this a very green enigine but still producing 330HP. Internal friction is another area which has had even more attention paid to, resulting in even higher response and acceleration which is sensitive to even minor throttle input. these points were touched on but not divulged completely, so more and more information about these improvements will be cleared up later in the year.

**Edit: VVEL DC motor controlled camshaft profile prounced 'Vee-Vell'

A DC motor is connected via threaded shaft to a 'control shaft' with a rocker arm attached, which then, via a link (shaped much like a conrod) moves another driveshaft which is positioned side by side to the previous mentioned 'control shaft'. The driveshaft had cam lobes positioned along the driveshaft, but are able to spin around freely on it, their profile is governed by the position of the driveshaft in relation to the control shaft; either being positoned closer or further away from it. What this essentially means is that the 'cam profile' is infinitely variable... there is no cam switching here, nor is there a 'switching point' or limits to the the camshaft profile (within reason). Variable Valve Event and Lift system or VVEL. My translation wasn't so good so... Check (if you live in usa): Publix Weekly Ad, or Big W toy catalogue.

Link to Nissan's VVEL explanation

gallery_4816_41_246561.jpg

The VVEL diagram

gallery_4816_41_63865.jpg

A better pic of the VVEL mechanism.

gallery_4816_41_152701.jpg

The VVEL page... sorry the flash covered the diagram with the electric motor mechanism and cams.

love it how nissan is finally looking into camshaft switching!!!

next step is 3d profiled camshafts - bring on ferrari technology!

on a downside - i can see this messing with alot of aftermarket turbo/tuning options.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...