Jump to content
SAU Community

Recommended Posts

Over drive OFF, power button ON.

Step on the break, rev up to about 2000-2,500 REVs.

Let go off the break and step on it.

:pwned:

For a stock converter practice with various revs between 2000-2600rpm, & also don't rev till the last few seconds otherwise trans temps will soar faster than you can say 'V-TEC power yo!'.

:pwned:

For a stock converter practice with various revs between 2000-2600rpm, & also don't rev till the last few seconds otherwise trans temps will soar faster than you can say 'V-TEC power yo!'.

Yeah... also don't do this shit on every set of lights lol (I mean at the track) :pwned:

I have an Automatic... I chosen it as a preference as Auto's launch just as good as Manual if you know how... and in a straight line (with good mods), Autos will beat Manuals...

HEre's what you do...

OVER DRIVE OFF, POWER BUTTOM PRESSSED, MAke sure you are running High Octane fuel (I personally like BP'S ULTIMATE)... Put it on DRIVE... Hold the BRAKE... REV TO AROUND 3,000 RPM's... LEt go of the BRAKE, step on it until around 4,000 RPM's and then pull it back to 2nd Gear to maintain the REV's at around 5-6,000 RPM's... then you just hold on it and pull it back just before you redline it... this is pushing the car to it's full potential.. most races are quater mile... do the above right and you will OWN....

I've always wondered about that... how does a burnout work in a AWD car such as the GT-R? Is it even possible without wreaking the ATTESA and seriously heating up the oils in the diffs/clutches?

If you are going to push your auto at the lights by holding high revs on the brakes, you should first fit a auto trans cooler because you will be generating a lot of heat which is the best way to kill an auto trans. A few hundred insurance against a few thousand for repairs.

Over drive OFF, power button ON.

Step on the break, rev up to about 2000-2,500 REVs.

Let go off the break and step on it.

I've always wondered too how the Autos do it, as I'm in a manual I dont get it.

If you put it in DRIVE and rev to 3000 and hold the brake, wouldnt that just make the car do a burnout while at a standstill?

Then if you let go of the brake you'll just get wheelspin and take off?

I've always wondered too how the Autos do it, as I'm in a manual I dont get it.

If you put it in DRIVE and rev to 3000 and hold the brake, wouldnt that just make the car do a burnout while at a standstill?

Then if you let go of the brake you'll just get wheelspin and take off?

If you dont rev over 2500 revs the car just barely creeps forward. Hence why in the auto revving around 2000 rpm is the best.

When you let go off the brakes, you will hit boost much quicker (3500 revs) hence a better take off. At the end of the day if you have good tyres, there wont be a big burnout... however this all depends on like I said tyres and how much power you run.

My car is stock btw.

I have an Automatic... I chosen it as a preference as Auto's launch just as good as Manual if you know how... and in a straight line (with good mods), Autos will beat Manuals...

HEre's what you do...

OVER DRIVE OFF, POWER BUTTOM PRESSSED, MAke sure you are running High Octane fuel (I personally like BP'S ULTIMATE)... Put it on DRIVE... Hold the BRAKE... REV TO AROUND 3,000 RPM's... LEt go of the BRAKE, step on it until around 4,000 RPM's and then pull it back to 2nd Gear to maintain the REV's at around 5-6,000 RPM's... then you just hold on it and pull it back just before you redline it... this is pushing the car to it's full potential.. most races are quater mile... do the above right and you will OWN....

Keep that up and u will destroy ur transmission in no time.

thanks guys. been meaning to ask this question but keep forgetting that i wanna know. is it possible to do a standstill burnout in an auto as well?

Fully depress the break, then fully depress the accelerator and u will start spinning the wheels (or maybe 1 if u have a worn out lsd :(. Back off before u change gears or this will stop the burnout.

I've always wondered about that... how does a burnout work in a AWD car such as the GT-R? Is it even possible without wreaking the ATTESA and seriously heating up the oils in the diffs/clutches?

personally I just dont bother. If you *must* be fulli sik get one of thoes awd -> 2wd switch's that go's in the fuse box, if you have a 32, or dont bother, if you have a 33 - 34

I've always wondered too how the Autos do it, as I'm in a manual I dont get it.

If you put it in DRIVE and rev to 3000 and hold the brake, wouldnt that just make the car do a burnout while at a standstill?

Then if you let go of the brake you'll just get wheelspin and take off?

Use the handbrake. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome!  Car sounds great, anypics ?
    • Welcome.  800hp should be a bit of weekend fun!
    • I'm going with "Just run two gates". Fix the problem conclusively. It's the only way you'd ever truly know, right?. This is all pretty much splitting hairs. Even the extreme example where it takes two whole seconds at 100kmh or something sounds monstrously dubious. And anyway, when you're punching the throttle when you 'need' this power, you aren't at 2800rpm in the wrong gear. Test it at 5600rpm in 3rd gear, when you're traction limited punching out of a sweeper. Much difference there when you account for traction?
    • And the full R32 GTR wiring diagrams are also freely available. Hmm.... there's supposed to be an auto replace that would have linked the thread. Here it is, manually  
    • Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
×
×
  • Create New...