Jump to content
SAU Community

Recommended Posts

Quote:

the theory is that with the cruise activated you not doing as much when driving such as looking at the speedo all the time to check your speed cos with the cruise you know its what you set it at hence no looking up and down every few seconds.....

As a truck driver I know that it makes it a hell of a lot easier to do the long trips!!!

Reading stuff like this makes my blood boil!!!! As a truck driver I know you MUST check everything all the time.

There are thousands of "experts" who continually remind us that we must concentrate when driving, no eating, no mobiles, no radio, no smoking... the list goes on and on. Yet the concentration of our driving public is getting worse. The more aids we supply, it seems the less concentration of the driver.

OK when I started driving, we had trailer brakes and truck brakes(no foot/hand combination), 24-speed quad box(2-gearsticks no synchro), 250max Hp, even had a mechanical hand on the door. Yet with all this action in the cab, we could dodge potholes while seeking out the smoothest part of the road ahead, watch the load, check mirrors.....

Now at 57 I can go outside, walk my excavator and take a swipe with the bucket while slewing. Not superman, just practice.

Education is what's needed, not gimmicks.

Some info: Cruise control can't see that big hill coming up. So if you wait until it drops into its operating range, you're down a gear before you know it. You MUST help it by booting it into the hills.

Sure it's great on the flat, but all this bulltwang about better economy is only from drivers who can't maintain a constant speed.

We've all seen them, 80 on the highway, 120 on the passing lane, I guess they need all the help they can get.

Some info: Cruise control can't see that big hill coming up. So if you wait until it drops into its operating range, you're down a gear before you know it. You MUST help it by booting it into the hills.

or you need a more powerful car.

I don't need to help the cruise control in my r33 by booting it into hills, it maintains speed just fine, maybe gains a bit down hills, but not much.

I believe it improves safety as when i have the cruise it takes a lot longer for me to get fatigued, which in the end leads to lapses in concentration.

It should not be used on country back roads when things can pop out at you, but on a dual carriageway freeway i dont see negatives to using it.

Quote:

or you need a more powerful car.

Too true. But seriously, get in an ordinary como or a falc and let them run at a hill with cruise on. At the top of the hill, check where the accelerator is. She'll be flat to the floor. That's not economical driving.

I get so sick of following shit boxes on cruise. You'll see them drop back to 90, then slowly pick back up to 100, then roll down the other side with the brakes on. You can really notice the stink from falc's and camry's running megarich.

All this in an energy conscious age.

Like I said, great on the flat but use your brains at the hills.

Quote:

or you need a more powerful car.

Too true. But seriously, get in an ordinary como or a falc and let them run at a hill with cruise on. At the top of the hill, check where the accelerator is. She'll be flat to the floor. That's not economical driving.

I get so sick of following shit boxes on cruise. You'll see them drop back to 90, then slowly pick back up to 100, then roll down the other side with the brakes on. You can really notice the stink from falc's and camry's running megarich.

All this in an energy conscious age.

Like I said, great on the flat but use your brains at the hills.

Dude dont use your cruise control in 60 KM area and or around sharp bends and hills and you will never have that problem. Keep it to the even level freeway where smooth, high speed, long distance driving is needed..

If you have the cruise set at 110kmph on the freeway its illegal to speed up fo the hill so you are still doing your 110 in your underpowered falcon or commodore at the top!!!

Dunno what truck your driving but mine tells me when something goes wrong......We are out of the Stoneage now.

If you were to drive a car without cuise and hit the same hill that the cruise control supplied full throttle for you too would have to plant your foot all the way up... but thats after you realized you were doing 90k's.

After a few yrs in a Aeromax with no cruise and 18speed RRanger then driving my new Sterling with 18speed auto and Cruise I feel much better after a days/nights driving.

Anything that can make my job easier is a bonus.... means Im more alert because I am not a fatigued.....IN MY OPINION!!!!!!!!!!!!!!!!!

Edited by Turbo Dave

I think cruise control is great when a lot of highway driving (i.e. interstate), but if you're just driving to work on the local freeway, it's probably not so safe. People pop out from seemingly nowhere, change 4 lanes at a time, talk on their mobile and break suddenly.

Also, it's not efficient on the windy or undulating roads. The first one's obvious (lots of speed changes required), the second one is that I find the cruise control system is reactive rather than proactive. A human will see a hill ahead and instinctively step on the gas a bit before the hill and likewise, ease off when nearing the top. The cruise control can't predict this, so it tends to struggle up the hill and overshoot at the top. This is assuming that generally you're in top gear (5th or 6th) on the highway, and has the least power/torque in this gear.

It's a great "nice to have" for those long trips to NSW or whatever -- who says that sports / hi performance cars can't drive long distances? It allows you to relax a bit and not have to worry about the speed as much. But still no substitute for being alert and concentrating.

Too true. But seriously, get in an ordinary como or a falc and let them run at a hill with cruise on. At the top of the hill, check where the accelerator is. She'll be flat to the floor. That's not economical driving.

I get so sick of following shit boxes on cruise. You'll see them drop back to 90, then slowly pick back up to 100, then roll down the other side with the brakes on. You can really notice the stink from falc's and camry's running megarich.

All this in an energy conscious age.

Like I said, great on the flat but use your brains at the hills.

i had it on my old vx commodore. hills don't suddenly go from flat to hill. there is usually a transition period. if you pay attention to the accelerator (rest your foot on it) you will see that as the hill gets steeper the accelerator goes down further. it doesn't just stay where it was then go "oh shit" and floor it straight away. it does the same thing you would if you were staying the same speed without breaking the speed limit.

how do they control the speed? i.e. what are they connected to?

most work off the ecu's speed sensor, the tps and they have a second throttle cable hooked up to the throttle body that goes into a little motor to pull on the cable to apply or let off the throttle.

Quote:

A human will see a hill ahead and instinctively step on the gas a bit before the hill and likewise, ease off when nearing the top. The cruise control can't predict this, so it tends to struggle up the hill and overshoot at the top.

I thought that's exactly what I just said.

Nobody drives at 60 with cruise on CCCP. Well maybe my dad but he loves his cruise.

Mad 082 I know how cruise control works and how you can alter your ramp rates etc.etc But if you don't have sufficient power to start with, as in your VX, you'll find at the top of the hill the acelerator will be right down. Check your torque curve on the VX. At cruising speed, it will be doing around 1800-2000rpm. Probably making about 50rwkw. Only takes the aircon to cut in and you've lost 5KW. Whereas if you'd dropped back a gear at the start, you'd be in peak torque range and the car would eat the hill.

As for the modern trucky Turbo Dave, keep at it. You've got a lot of miles to catch up.

I think cruise control should be banned on cars i think it causes crashes

You should write articles for the police force.

As for using less fuel, I found it the opposite in both my commodore, and my dads commodore, was adding around 1 - 2L of fuel required per 100km.

As for not getting done. Ever looked down whilst coming down a hill? I found my car, and also my fathers, loved to just hold the throttle open coming down a hill till your doing around 10-15km/h over the limit, then it'd close the throttle SOME, but not all the way.

My uncle also got done for speeding on Cruise. Car set at 100km/h, copper pulled him at 112km/h going UP a hill (Car decided it had slowed a bit, needed more power, so it changed down a gear *auto* and accelerated, to above the limit)

I've had it in my old car, and I did use it, but I had to be ever so vigilant, now that the skyline doesn't have it, I get in a car with CC and don't even use it.

Also, you shouldn't use cruise in the wet either.

Edited by MBS206

I'm a big fan of Cruise. I use cruise everywhere, including on 50kph streets. I hate getting fines (not that I've had one in the last 5 years) and so use the CC as a speed control device. Accelerate to speed limit, activate cruise.

It's easy, it's what it's there for and it works. My wife's VW GTI had an instantaneous litres/100k readout and on a flat surface the thing is rock solid. Undulating, I've never seen the cruise be more than a few kph behind set speed going up a hill, and I've NEVER seen it over the limit anywhere other than a a very steep hill, and at a very steep hill, even if you don't have cruise, you are going to accelerate.

I think the argument about things jumping out at you on suburban roads is a little misguided. In these days of constant speed watching, it could be said that cruise is a safety device. The less time I spent looking down at my speedo, the more time I'm looking at the road ready for those things that "Jump out at me"

I hate not having CC in my R34, especially on the trip to Deca when you want to relax and constantly be speed checking. I have done a LOT of kilometers for work in cars both with and without cruise. I'm much more alert and less tired after a few hours on cruise than not. This makes me a safer driver on cruise.

I had cruise control fitted to my stagea. I am cruise control freak. (most people think just control freak!). I luv it. Not only for trips but also around town. I even use it sometimes in the school zones (40kph). You just never know when Mr Plod is going to be pointing a radar gun at you. Oh I turn it off for drag racing though!

Oh yeah $640 at Cruisewest. Nice unit, on the wheel, Looks like Nissan fitted it.

Edited by Appealing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...