Jump to content
SAU Community

Recommended Posts

yeah I was going to use some 340mm rotors I have with the standard calipers. but now that I have these brembos i may as well use them. mainly because they have a larger pad, and should be a stiffer caliper.

if you do want to use 324mm rotors with the stock calipers I'd reccomend the UAS kit. Very, very nice brackets. and not a bad price either.

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

just so happens that the tread is alost right. just abit tight. so the tap makes it slightly bigger by about 0.2mm so worst case you can still use the calipers on a 34.

I'm not sure what you mean dave-o? you mean I can drill my hubs to take the 14mm bolts for the 34 caliper. and then if I ever wanted to go back to stock caliper I could just cut a new thread in my standard 32 caliper to accept the 14mm bolt?

here's a couple of dodgey pics I snapped just for you ronin. the gold is a bit camp, but I must admit they are a good looking caliper. If I thought I could get as good a finish as factory I would paint them black for sure.

picture047ms4.jpg

picture052el0.jpg

yeah also missing rotors, lines, pads... no, I have everything. I just didn't take pics of it all.. there are no shims in the rear calipers as there are no pads in there.

as for you ronin... don't poke fun at my gold brakes. at least they are factory painted unlike all the cool people who paint their sumitomos gold to make slow witted people think they have brembos...

eug, yeah your black stockies look ok, but I don't like the finish on them (which is why I wont re-paint the brembos). It just doesn't look quite right to me.

yeah I was going to use some 340mm rotors I have with the standard calipers. but now that I have these brembos i may as well use them. mainly because they have a larger pad, and should be a stiffer caliper.

if you do want to use 324mm rotors with the stock calipers I'd reccomend the UAS kit. Very, very nice brackets. and not a bad price either.

Hmm interesting. I was always of the understanding that the pad in the Brembos on the Nissan was bugger all larger than that of the Sumitomo's. Any chance of a compare & contrast?

Gold: The new black?

Or

Gold: As camp as a row of pink tents?

yeah, I'll whip one of the pads out tonight and do a little comparo. it's not a massive size difference, but it looks bigger to me. god I hope there is some advantage as they are not that cheap! i'll cling to the faint notion of a stiffer caliper.

eug, yeah your black stockies look ok, but I don't like the finish on them (which is why I wont re-paint the brembos). It just doesn't look quite right to me.

yip... it's impossible to get the same smooth glossy finish in black without spending some decent coin for temp resistant paint.

they get dirty anyway, so i wasnt too fussed.

yep, that's what I meant. i guess it would want to be to take advantage of the larger diamter rotor. :D

Well yes & no. It is not so much the diameter of the rotor as a whole, but more so the depth of the race of the rotor. See the attached photo for an ugly example of what the things shouldn't look like. You can see that there is a fair amount of rotor face not being wiped by the pad & also that the inside radius of the pad is quite a bit different to how it should be.

It is something to be a bit careful of when buying aftermarket calipers & rotors - particularly if you are mix & matching.

post-5134-1176949404.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...