Jump to content
SAU Community

Aluminium Drop Tanks

Public Enemy
 Share

Recommended Posts

Public Enemy Community Regular

Public Enemy

Posted
Posted

After reading posts about the in car fuel smell associated with surge tanks mounted in the boot i was wondering if having an aluminium drop tank (SLR5000 style) built with an in built surge tank would be feesible. I guess it's just a matter of more money!!!

I would also go for added baffling in the tank as well or maybe that foam stuff you can get for motor bike tanks.

What do you think?

I guess getting to the fuel pumps may be a little more difficult.

ANyone know where i could get one built in Perth?

cheers

Paul

Link to comment
https://www.sau.com.au/forums/topic/165166-aluminium-drop-tanks/
Share on other sites
Craved Grand Master

Craved

Posted
Posted

Or use a sealed box as legally required if you have it in the boot.

as for the drop tank, to remove the wheel well and reinforce the area, then have the drop tank installed and engineered . it will cost you a fair bit.

have thought about this before though .. you also shift the balance of the car since the std tank is over the rear sub frame, this would move the weight back and potentially cause some over steer characteristics when full tank and cornering

Public Enemy Community Regular

Public Enemy

Posted
  • Author
Posted

Thanks for the replys guys.

Might as well get a quote for one i guess cheers for the contact details bubba.

For those that have mounted underneath, what size surge tank did you use? I was planning to run Sard 7.5l with twin bosch044's.

Thats a pretty big tank to hang underneath.

dontfeelcold Experienced

dontfeelcold

Posted
Posted (edited)

If you were going to the trouble of a drop tank, you should also put baffles and trap doors in the fuel tank, this forces the fuel into the front centre of the tank. Just like your engine sump. Also bend the top of the baffles into the centre to stop the fuel from sloshing out of them.

Edited by dontfeelcold
Public Enemy Community Regular

Public Enemy

Posted
  • Author
Posted

What setup does this car have that requires something that large?

2.5ltr would be enough for most easily

can you fit 2 x 044 pumps inside a 2.5L? I was looking at the 7.5 because it says its big enough to fit 2 bosch pumps, thats the only reason i would use one so big.

Don't care if it looks good or ghay, it's not there to change the look of the car or an attempt to grab rice points or look like a Torana ffs. in fact it would be painted matt black so you prolly wouldnt even notice it.

Anyways i thinking just mounting the surge tank underneath is the way to go.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Why would you ut the pumps inside? I dont get it. :nyaanyaa:

It goes like this

- You have a lifter/feeder pump to the surge tank.

- From the surge you run whatever pumps you need external of the surge tank.

- The externally mounted pump(s) feed the fuel rail

GeeTR Grand Master

GeeTR

Posted
Posted
can you fit 2 x 044 pumps inside a 2.5L? I was looking at the 7.5 because it says its big enough to fit 2 bosch pumps,

:D

I too didn't want the surge tank in the boot, or have to run $$$ lines just for smell. I'm currently mocking up a s.tank to fit up under the car, in front of the f.tank. Stock pump as a lift, then a 044 sitting OUTSIDE the enclosure pushing fuel up front.

PS: Has anyone else heard, that you can get increase knock value from driving hard with below 1/4 fuel in a BNR32?

25GTT Veteran

25GTT

Posted
Posted

Yup Briffa engineering in Morley, has already done a couple on the 33 gtsts anyway. Ask for Mick he is the owner

A very old school friend of mine, tell him webby sent ya, i used to sit next to him and get in trouble for laughing all the time.... oh those were the days.

He has done plenty of work to mine and am happy with the results!

Public Enemy Community Regular

Public Enemy

Posted
  • Author
Posted
Why would you ut the pumps inside? I dont get it. :P

It goes like this

- You have a lifter/feeder pump to the surge tank.

- From the surge you run whatever pumps you need external of the surge tank.

- The externally mounted pump(s) feed the fuel rail

why mount them out side when you have them inside, i don't get that. Especially when there under the car getting hit with rocks and covered in dust and water.

All the drawings i've seen from sard show the pumps inside the surge tank.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Can u check this way it works for power supply?
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      These coils draw 10amps that what i read online
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...