Jump to content
SAU Community

Nismo 740cc Injectors -- Too Small ?

Guilt-Toy

By Guilt-Toy,
in Engines & Forced Induction

 Share

Recommended Posts

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

I am after the magical 500rwhp and I have been told by a few people that the Nismo 740cc injectors wont cut the mustard and that will need to upgrade to a 1000cc injector.

I cant really believe that this is true.. does anyone know what power nismo 740cc injectors would be good for ? its on my RB30DET.

I dont really want to run more then 92% injector duty

Link to comment
https://www.sau.com.au/forums/topic/166249-nismo-740cc-injectors-too-small/
Share on other sites
Pauly33GTS-t Veteran

Pauly33GTS-t

Posted
Posted (edited)

or is it 15 to 17cc = 1 hp ... i forget.

EDIT: I think that's at engine... and a typical calculation for normal modern cars...

Im sure that Nismo 555cc injectors are rated 555hp, and 740cc injectors are 740hp...

Edited by Pauly33GTS-t
MANWHORE Grand Master

MANWHORE

Posted
Posted

Nismoid, do you have 360 rwkw in your r31? far out, she must chirp seconds. how's the response? like when do you get full boost by? rb30, 25 or 26?

Anyways, so answer your question, sydneykid usually says the cc rating is approximately equivalent to the hp.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...