Jump to content
SAU Community

Recommended Posts

this

my car feels just as quick on 7psi than on 10, should prob put it back and see what the economy gets like

living in tasmania definitely throws the economy out the window, barely a straight road about

not that i'm complaining :P

Knock sensor maybe hearing a rattle on 10psi and taking out some timing.

Oz

Knock sensor maybe hearing a rattle on 10psi and taking out some timing.

Oz

its been running 10psi for ages and i've only run 7 once for about 2 mins so i haven't really tried it all that much

i've got a spare switch hanging around so i might wire it up to have a selectable ground

i should really pull my finger out and the the jaycar iebc installed but i really cbf

its been running 10psi for ages and i've only run 7 once for about 2 mins so i haven't really tried it all that much

i've got a spare switch hanging around so i might wire it up to have a selectable ground

i should really pull my finger out and the the jaycar iebc installed but i really cbf

Please M8 be careful with using stuff from Jaycar, its all made in China and is mostly crap.

Oz

The stagea you have is based off the R34 engine and turbo. Technically this means it should be more efficient, but obviously not in your case. The exhaust without any tuning will not help your fuel economy. You'll get more power (and the exhaust means you're running more boost - probably around 11psi) but it'll just run really rich on the factory tune. Get some kind of piggyback ecu in there and a proper tune and you'll see a huge increase in both power and fuel economy. In my case it went from ~13L/100km to 11.5L/100km just driving to work and back. Admittedly it didn't help the hwy economy much but I was getting 10.5L/100km consistently which should get around 600km to a tank (roughly 60L at the empty line - tank itself is 68L)

There are a lot of people on here getting >400 (some > 450) kms to a tank in the city. I suggest you do take it to a dyno and get the AFR's checked out...and check for any error codes from your ecu - might have a faulty sensor somewhere. Other things to try is clean the AFM - remove it from the car, run some contact cleaner or metho over the metal wires that hang down inside the pipe (but dont touch them with your fingers), let it dry, then put it back in.

to anyone else out there not used to the way Nissan ecu's respond on turbo cars - if you get a free-flowing exhaust, you MUST get some sort of aftermarket tuning - like a piggyback ecu (eg. apexi safc or greddy emanage).

So many people think an exhaust will make their car run leaner. not true (well, not for these cars anyway). The exhaust affects boost pressure in that your boost limit increases - and obviously the amount of airflow increases too. The ecu reads the amount of air using the AFM and then adds the appropriate amount of fuel - according to its pre-programmed fuel maps. Due to the amount of airflow you're actually getting with a 3" exhaust, this causes the potential to run dangerously lean so the ecu will compensate by adding ridiculous amounts of fuel, and its not uncommon to see AFR's below 10:1 just from adding a 3" exhaust. somewhere around 9.5:1 the ecu will panic and go into R&R (rich and retard) mode to protect your engine. It feels like a sudden loss in power and you'll get it when under hard acceleration. In extreme cases, it will cut fuel and it'll almost send you through the windscreen.

Short answer: If you get an exhaust, or even if you just add more boost, get it tuned. You'll never get the best from the exhaust if you dont...and it'll cost you crazy amounts in fuel.

I agree, the Neo2 was sposed to be better, i just havent seen it yet :)

Also on the exhaust, I only noted that for accuracy, I do not agree with your comments there, by just fitting a more free flowing exhaust the ECU should not need remapping.

It will also have a negligable affect on fuel acconomy. It may end up giving you a little more in the way of boost (maybe) but the ECU will easly cope with that.

As im only talking about fuel eco, im only talking about light load conditions.

Cleaning the AFM I have done in the past to fix some probs, but ill give it a run on the dyno first to see whats going on first i think.

Im not 100% sure on the Stagea, it may have a AFM clean/Burn mode built into the ECU..

I have checked O2 Sensor and ECU codes. All fine.

Like I said, im going to run it up in the next few weeks i hope is i get time, Ill document AFR,load etc and timing. And we will see whats going on... Maybe there just a brick! lol

Thankyou for your comments

Oz

PS. just wondering, you in the Trade?

I agree, the Neo2 was sposed to be better, i just havent seen it yet :D

I owned a neo (1999 stagea) for 2 years and averaged about 13L-14/100km when it was completely stock.

Also on the exhaust, I only noted that for accuracy, I do not agree with your comments there, by just fitting a more free flowing exhaust the ECU should not need remapping.

I think you misunderstood my point - its not that it NEEDS remapping in order to run. But if you get it remapped, the benefit is huge, enough that I no longer see the point in upgrading the exhaust and not tuning the ecu. You're just not seeing the full benefit until you remap the ecu or add some form of tuning.

It will also have a negligable affect on fuel acconomy. It may end up giving you a little more in the way of boost (maybe) but the ECU will easly cope with that.

Admittedly I had a high-flow (GT30 hybrid) turbo installed before I upgraded my exhaust but my results matched what most people on here said. Once the exhaust went on, boost went up to around 11psi, and my fuel economy suffered due to the extra performance potential (I can be a bit of a leadfoot sometimes). 11psi was also enough for it to run AFR's below 10:1 and hit R&R and fuel cut on occasion. This could've been due to the upgraded turbo though.

Obviously if your driving style didn't change then your fuel economy wouldn't be affected much, but my reasoning was that most people after fitting a free-flowing exhaust will adjust their driving accordingly, resulting in more fuel usage. As you increase boost, your fuel-efficiency gets worse and worse - because the ecu tends to severely over-react by adding crazy amounts of fuel.

The reason I recommended tuning is because of the result I saw after getting a SAFC installed and properly tuned. When I first had the SAFC installed it had only very mild adjustment - enough to stop it hitting R&R but not much else. Later I had it tuned by a more professional tuner and also the base timing was advanced to suit. The result was a decrease in fuel consumption from 13-14L/100km down to just 11.5-12L/100km and this was consistent from that point onwards.

As im only talking about fuel eco, im only talking about light load conditions.

fair enough.

PS. just wondering, you in the Trade?

Haha No. I'm actually a computer programmer.

I only know bits and pieces that I've picked up off the forum combined with personal experience from having owned 2 stageas over 3+ years and other nissan imports for over 5 years before that. :D

Full tank of United Premium-100, and to the first petrol light i got 404kms. Then drove till about 425 and refueled, didnt want to run out hehe.

And this was what I qould call 'average driving'. Was a mix of some highway, city, suburb, steady and 'spirited' driving.

If I really babied her, I could squeeze over 450 I think.

Its still stock apart from a 3" Cat back including new 3" Cat, but plan on some mods and especially a Power FC and tune

Please M8 be careful with using stuff from Jaycar, its all made in China and is mostly crap.

Oz

lol so is the computer you typed this on. do you have a particular concern with specific bits of their stock or do you just beleive nothing from china can work???

managed to pull 480kms from this tank (light has been on for about 20kms)

that has included running through town, 4 hours on the highway with several straights and overtaking manoeuvres and 30ish mins going over some mountains = fun

i've hooked up an on/off switch to the grounded side of my solenoid and ran it into the cabin and grounded it there - basically allowed to have 5-6psi max with the switch off and ~10 with the switch set to on

not sure why mine is 5 and 10 tho (thought it was 5 and 7 stock) makes a big difference, can notice the lack on high boost on accel but as i figure the stock maps go very rich on 10psi and are much leaner on 5-6 so it may take more throttle input to get it to move on low boost but at least it will be running a bit leaner

I'm getting on average 512 kms to the tank on 98 RON. Thats with a full system, FMIC, bigger boost, HKS pod filter and a few other supporting mods.

That is all. :laugh:

Okay, so what i think is a stock RS4 Series 2; My last two tanks are as follows:

Tank 1: 47L and i got 430.7km-10.91L per 100k. This was with about 10% spirited driving and the rest a pretty even split between highway and urban.

Tank 2: 56.2L and 519.3km-10.82L per 100k. This was with more spirited driving then last, however i also drove to Toowoomba which was about 2 hrs. and 15 minutes on highway at a average speed of 100kmph. The rest was suburban and city driving.

All done on Bp 98 ron. :nyaanyaa:

yeh filled up 2nite petrol light had just come on, 530K, and topped up 56L....car due for a service too, and again its BP 98 Ultimate....which i also gotta say is alot of the time cheaper then other stations 98...

has anyone else tried 98 from mobil? we've found that you use it about twice as quick as BP 98... we tried it when driving from Brisbane to adelaide, so same driving circumstances as all the other tanks of BP 98 we had...

has anyone else tried 98 from mobil? we've found that you use it about twice as quick as BP 98... we tried it when driving from Brisbane to adelaide, so same driving circumstances as all the other tanks of BP 98 we had...

Hmm i always rated Mobil. In my old car i would normally see about 50km+ more per tank with it?( in my first car, a Subaru liberty wagon)

has anyone else tried 98 from mobil? we've found that you use it about twice as quick as BP 98... we tried it when driving from Brisbane to adelaide, so same driving circumstances as all the other tanks of BP 98 we had...

i used to use it, seemed good and i got average fuel consumption with it

i know its not a stag but the gf's grandparents always use it in their audi and they see 8l/100km city and getting down to almost 6 on the highway!!!! and its the turbo one too, and its a solid car - damn germans

also, if you want basic control over your boost then you car chop off just the neg (grounded) side of the stock solenoid, connect some wire to the solenoid side of what you chopped and run it into the cabin, grab an on/off switch, connect your wire to one side of the switch and earth the other

that mean that with the switch off you will run whatever you car runs before 4500, but will do it all the way to redline

flich the switch to on, you get max boost all the way to redline

there have been stories of the stock solenoid getting burnt out if grounded all the time - this is a way to have the best of both worlds

haha yeah i could imagine. Pipster, isn't that a bit risky? What happens if the car detects knock but you have the ground un-slected or whatever and its running 7-8-9psi? I want to do something similar once i get my nistune installed, but i was warned agiasnt it for that reason.

I also would like to say, i really hope to see under 10l per 100k after my nistune install, hi-flow panel filter and turbo back exhuast. All in good time though haha.

haha yeah i could imagine. Pipster, isn't that a bit risky? What happens if the car detects knock but you have the ground un-slected or whatever and its running 7-8-9psi? I want to do something similar once i get my nistune installed, but i was warned agiasnt it for that reason.

I also would like to say, i really hope to see under 10l per 100k after my nistune install, hi-flow panel filter and turbo back exhuast. All in good time though haha.

pretty sure if it hears a knock then the ecu pulls timing and dumps fuel

i've been running it for a couple of weeks and i leave it mainly on low cos if i'm on the highway and go to overtake it will at 10psi before you know it

and how i see it 40% throttle with 10psi or 60% with 5-6psi - cos the stock maps are so rich once you get up to ~10psi its gotta use less fuel

i did a trip to the coast, 150kms each way and used about 17 litres to get there which included going through some fun twisties - only 2 ppl in the car but 1 huge ass 12 man tent, 4 surf boards, 1 body board, 1 esky, clothes, doona and other random shit and not driving lightly really

on the way back i think i got closer to 10 (something like 10.2 or 10.5)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...