Jump to content
SAU Community

Recommended Posts

post-38769-1179790657_thumb.jpgHi - brand new to this board. And brand new to me (bought yesterday at auction in Kobe) is what I think may be the only Stagea Autech Axis version in Australia when it gets here? I'll post more later, but here's the spec:-

2004 Nissan M35 Stagea Autech 4WD Axis with VQ25DET motor (206kW, 407NM)

Autech suspension

Autech 18" factory mags

Autech body kit

Fujitsubo sports exhaust

Xenon (HID) headlights

DVD/TV/CD-MD/Satnav

Cream leather trim

5 speed tiptronic auto

Blinkers in side mirrors

Viper alarm

Now waiting on DOTARS to issue the import approval. My buyer says the car "drives like new, smells like new, looks like new". Rated 4 but should have been 5. 47,000km.

Can't wait!

Have posted pics in my gallery:- http://www.skylinesaustralia.com/forums/in...i&img=61812

As I'm a newbie more advice about posting pics would be great, if anyone's interested in seeing them.

Look forward to advice about performance mods and comments about the styling (I like this car, but sure some will not!).

Edited by autech_axis
  • Replies 87
  • Created
  • Last Reply

Top Posters In This Topic

wow - nice one!

couple of questions thogh, Is it only available in an auto? I thought the main advantage of the Autech was that it was a manual?

Also, what difference is there mechanically between this and a usual 25T X four?

As for photos, you are best using a static IP hoster such as photobucket and direct linking from there, or just upload to your gallery and link the way you have done.

And welcome!

wow - nice one!

couple of questions thogh, Is it only available in an auto? I thought the main advantage of the Autech was that it was a manual?

AFAIK auto only. I couldn't find a manual at auction.

Also, what difference is there mechanically between this and a usual 25T X four?

There are dozens of different variations of the NM35 Stagea. This one has everything except sunroof. So, same engine / transmission as 250T RS Four V. The Autech contribution is limited (AFAIK) to suspension and body / interior mods only.

These cars are quite rare in Japan, and command a very high premium over the 250T RS Four V. There 's also an Axis S version which has 17" mags, different body kit and less glamourous interior.

As for photos, you are best using a static IP hoster such as photobucket and direct linking from there, or just upload to your gallery and link the way you have done.

And welcome!

well done mathew looks very tidy, be keen to hear how it goes(got anymore pics...is it badged autech),like i mentioned in the just joined thread i can feel a stagea meet coming on.

well done mathew looks very tidy, be keen to hear how it goes(got anymore pics...is it badged autech),like i mentioned in the just joined thread i can feel a stagea meet coming on.

As you might imagine I'm like a kid with a new toy, waiting for Xmas! I've got some hi-res pics from my buyer in Kobe and have spoken at length with him about it - goes very hard apparently and presents pretty well as new. Some of the Axis cars I've seen have a little Autech badge on the rear bumper, but for some reason this one doesn't.

I'll be itching to show it off in a couple of months.

Anyone know anything about tuning VQ25DET?

post-38769-1179798094_thumb.jpg

post-38769-1179798182_thumb.jpg

post-38769-1179798230_thumb.jpg

hey matthew or any other guy's i'm not really up to speed on later mod stageas but didn't nissan drop the turbo & go 35 v6's after a certain year...what year i'm not sure...anyone shed any light?

hey matthew or any other guy's i'm not really up to speed on later mod stageas but didn't nissan drop the turbo & go 35 v6's after a certain year...what year i'm not sure...anyone shed any light?

July 2004 was the last of the M35 turbos.

wow - nice one!

couple of questions thogh, Is it only available in an auto? I thought the main advantage of the Autech was that it was a manual?

Also, what difference is there mechanically between this and a usual 25T X four?

As for photos, you are best using a static IP hoster such as photobucket and direct linking from there, or just upload to your gallery and link the way you have done.

And welcome!

Out of all the M35 Stageas, only the Autech AXIS 350S came in manual from June 2003 to July 2004.

Like has been mentioned there are many different types of AXIS models from 2.5L to 3.5L, RWD to 4WD, turbo and non-turbo, with varying equipment levels. But the Axis 350S was the only MT variant from new.

wat are the differences between the normal m35 and an autech one?

It's merely a styling package with alot of the optional equipment offered in usual Stageas (depending on model) as standard, as an example, the only options available for Axis models were floor carpets, 'neoncontrol' (those little pop up antenna things that help you judge where the left front coner of the car is), and plastic side window visors.

apart from the body kit and rims? how about the engine?

Nothing... it's not a performance variant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...