Jump to content
SAU Community

Recommended Posts

I might be up for a new clutch as mine is acting up a bit - shuddering and squealing like a b!tch - more than usual but not sure exactly what's up until I get the gearbox dropped.

I was wondering whether there is anyone with a Xtreme 7 or 9 puck ceramic clutch in their car that I could take for a drive just to see exactly what it drives like? I live in Heathridge (NOR). I've heard some good things about them but I'd like to speak to someone who has upwards of 300+ rwhp (as does my r33).

-Alan

Link to comment
https://www.sau.com.au/forums/topic/169997-xtreme-clutch-test-drive/
Share on other sites

I have a 9-puck & over 400 with no problems, still drives fine :)

That's what I like to hear :) How long have you had it installed?

Also - how much are the clutches for R33? and how much also to do get installed? Prices will differ depending on where it was done I assume.

That's what I like to hear :O How long have you had it installed?

Also - how much are the clutches for R33? and how much also to do get installed? Prices will differ depending on where it was done I assume.

Had it for about a year or maybe less now. 350rwhp when I got it, 385 for most of it & over 400 at the moment. Cost me around the $900 mark installed *I think*

  • 3 weeks later...

The 9 puck with a 'sprung centre' friction plate and the stock pressure plate is very good. People frequently over-do the pressure plate. The clamping force on the stock R33 unit is quite sufficient for a street driven car. The friction plate does all the work it just needs 'enough' pressure to make it work.

The same 9 puck friction plate is in a friends 300+rwkw GTR and has covered 30,000kms of aggressive driving.

My old R33 I setup with the 9 puck friction plate and factory stock pressure plate, it feels exactly like stock. It was a low 13/high 12 car and at one stage had a 100+rwhp extra shot of nitrous before selling the kit off to 2rismo over east. So that was plenty of torque and power with no slip. Go extra clamping pressure for more aggressive sustained high rpm driving (like circuit or drift), the trade off is pedal effort and wear on the clutch components.

Bung a light weight chromemolly flywheel in while your at it.

i got a 9 puck extreme clutch put in about 2 months ago and feels pretty much stock except it springs back a little bit quicker. if you didnt know it was in i dont think you could tell plus i drive it on the street and its easy...the old man drove it and hes got a dodgy knee and found it alright so cant be too bad haha

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...