Jump to content
SAU Community

Recommended Posts

OK, due to the fact that the Stagea is such an unusual vehicle, I have decided to start a thread covering other wacky wagons. I have had a (rather unhealthy) obsession with wagons for a long time and I thought now would be a good place to share some of the oddball creations I have come up with. Feel free to post up links / pics of any others you have found – particularly the Mini Traveller Estate I keep hearing rumours about, but have never seen (no, I don’t mean Bonspeed’s concept)

First up, the Mustang wagon!

carlifewagon.jpg

estatewagon2.jpg

Or, how about a V12 Lamborghini?

330gt_05.jpg

330gt_03.jpg

330gt_11.jpg

Link to comment
https://www.sau.com.au/forums/topic/172298-the-wacky-wagons-thread/
Share on other sites

  • Replies 191
  • Created
  • Last Reply

Top Posters In This Topic

bv_kloepfel1.jpg

Ferrari 250GTO "Breadvan"

In 1961 Count Giovanni Volpi wanted to race a 250 GTO but Enzo Ferrari refused to sell him one. Se he took a 250 GT SWB and modified it to GTO specifications. At the same time he had Piero Drogo clothe it with a body designed by Giotto Bizzarrini and based on the aerodynamic theories of Dr. Wunibald Kamm. The car was 6 inches lower than a 250 GTO. In spite of a higher top speed, it was only moderately successful. Best placements were a 2nd at the 1961 Tour de France and a 3rd at the Monthlerey 1000-Kilometers. However, with its nickname "Breadvan" (Camionette in France), it became world famous.

Porsche 924 built by DM Motorsports in Germany

924_06.jpg

*edit - this car isn't actually a wagon. Because it only has 2 side doors, in Europe it is known as a "shooting brake" and no, I don't know why either

1976_Cadillac_Castilian.jpg

Check this out! Remember this thing the next time you winge about the fuel economy of your Stagea. :thumbsup: This is a 1976 Cadillac Castilian. Its 19.5 feet long (9.2m), weighs 5500 pounds (2500kg!!!!!) and was powered by a carbie fed 500ci V8.

Updated current model Ford Mustang

ford_mustang_shooting_brake.jpg

For all of us Skyline and Stagea drivers who are/were Corolla drivers, how about the good ol' Tercel/Corolla 4WD?

vgv_1121086212_tercel1.jpg

ty1983tercel01.jpg

larsc_wagon03.jpg

Bil%20Corolla%204WD%202002.jpg

The Pontiac Solstice:

EDAG_Soltice_3.jpg

The Audi Shooting Brake concept (yep, its official name):

Audi-Shooting-Brake-Concept_rear.jpg

Audi-Shooting-Brake-Concept.jpg

0510_tokyo_01%202006_audi_shooting_brake%20front_side_view.jpg

414831db619ba8c1e9710990b0584848_1.jpg

The Renault Altica:

26brake_slideone.jpg

The Porsche 924:

924_Turbo_Break.jpg

FYI - the Sultan of Brunei has had HEAPS of custom cars made up by all the big makers, and quite a few of them are Shooting Brake/Estate/wagon versions of supercars and luxury cars... Lucky bastard!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...