Jump to content
SAU Community

Recommended Posts

Thanks. :(

Hi- I need the part number number for the centre mesh grille (between the headlights on the Nismo model) for a R34 GT-t. The VIN no. is 6u90000cr34006857 Paint Code is QM1 and build date ie 06/09

regards Carey

Sorry bout forrgeting to check back. for future referance u can drop off the 6U90000 from the beginingof the vin japanese vins are only bout 10 digits long they add the 6U part when they do the compliance stuff because australian vins are 17 digits long. Also it ER34 not CR34 (fsecond picture)

Part NO. to suit QM1 code 62310 AB104. not applicable for your year model car/vin unless it has the type of bar that is in the first pic

hope it all helps

post-42804-1210075015_thumb.jpg

post-42804-1210075062_thumb.jpg

Edited by neofenrir34

I'm after the part number for the ignition coils on a 1997 S1 Stagea WGNC34 - Same engine as Series 2 R33 GTS-T's

I'm also after the main seal for the front diff and also the gasket that goes on the back of the ATTESA actuator that connects the ATTESA reservior to the gearbox (can provide pictures if need be)

Thanks! :P

  • 3 weeks later...
  • 2 weeks later...
Part numbers for rubber brake lines on r34gtr (not n1) and if they are the same part number for the rubber brake lines on r33 gtr and/or 32 gtr.

Cheers.

Part No. 46210-6L110 RHF, 46211-6L110 LHF, 46210-21U17 X2 Rear hoses

I'm after the part number for the ignition coils on a 1997 S1 Stagea WGNC34 - Same engine as Series 2 R33 GTS-T's

I'm also after the main seal for the front diff and also the gasket that goes on the back of the ATTESA actuator that connects the ATTESA reservior to the gearbox (can provide pictures if need be)

Thanks! :D

fairly sure that the part No. for the ignition coils is 22448 25U00. not sure which seal u are reffering to as the main seal in front diff. and can't find the gasket you are talking about for the ATTESSa actuator

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...