Jump to content
SAU Community

Recommended Posts

Would i be right in saying that the oil flow in an rb26dett engine follows this direction.

from the sump oil is picked up by the oil pump and pumped out through the oil / water heat exchanger. Then from there out,to the filter housing and from there out to the oil /air coolers and then returned to the filter housing and into the oil galleries to supply the slippery stuff to all those rotation parts.

The reason i ask is that i installed another oil temp guage into the filter housing and iwas wondering if i installed it into the return line from the coolers as i have about 50 degrees of temp difference between the stock guage and the after market item and for the life of me this is the only possible reason my brain could come up with?

Link to comment
https://www.sau.com.au/forums/topic/173026-oil-flow-question/
Share on other sites

don't you want the temp after it's filtered and through the inline cooler - as this is what is protecting all the up and down bits.

once it is run through the engine, it drains to the sump so it's hotter there but it's more important to have the pressurised temp reading.

mine is tapped into the return from the oil cooler (i tihnk)

Yep not sure where the factory guage is installed but would be really surprised if the 2 coolers i have would provide 50 degrees of cooling. I need to check the after market guage with some heated fluid to confirm it is reading right. As the stock temp gauge is nugging 120 ( well i think it is as the mark below the 150 line ) and the after marketone isreading only 80 ish.

  • 4 weeks later...
best pickup for oil temp is sump

Bump...............within this temp range.............best way to test pesky temp senders/recievers is ice cubes in water (sustained) ~4deg C (nice low end point) & boiling water ~100deg C (ballpark high end point). At mean sea level. Ifya got all the sensors/reciever loops cooling/cooking at the same time yer onto it.

Cheers

My english'ised comment ?^^?

I'm not so sure about placement either. I would assume post cooler, so you know the temp of the oil going into the motor... but whats the point if its going in at 80c and when it finally hits the cam, crank etc journals, its 150c and breaking down? (I'm sure its unlikely where there are near by water jackets at a constant 90c or what not)

*ponders*

Correct i really am not bothered about what temp the oil goes in at. The only time i will bother with that is if the oil coming out is about 120 odd. At this point i will then look and see what temp the oil is going in at.

I still do not believe that the air to oil coolers can possibly drop the temp down 40 ish degrees, or the fact that i am only just reaching 90 degrees on the the coolant temp while the oil temp is so high it just doesnt make sense to me.

Any one else have some figures to see the difference between the oil and coolant temp? Or had problems with the stock oil temp gauge

URAS,

I cant tell you a brand as it was on the car when i got it. Still located in the original position on the side of the block, and i have removed one of the ellen key grub screws and install the electric temp sender in to this position, hence i am not sure if its measuring the cooled oil returning from the two coolers in series. Or a shitty sender in the first place and why i have such a big diff between the readings on the 2 guages.

Where o where does the original oil temp gauge have its sender located.

Cheers guys thats what i wanted confirmed.

Now WTF how could i have 40 odd degree diff between 2 gauges that are within inches of each other unless one is one the outlet and the other is on the return side of the filter housing.

Is it possible to get 40 degree of cooling from 2 air to oil coolers mounted in series.

Or is the engine to hot and produce oil temps of 120 - 125 degrees while engine coolant gauges ( 3 of ), 2 show low 90ies and the stock gauge sits mid way on its scale.

what brand gauge?

the reason i asked about the filter mount is the brand would let me know if the port was in the in or out side, if your gauge is a reputable electric brand it should be accurate, it maybe worthwile to swap the two senders around and compare the results. I run my oil temp and pressure off the remote mount and it is very accurate.

Hmm, not so sure as the coolant temp gauge reads the same as the PFC. But good point i will buy some better gauges in Oz next week while i am home and see if that makes any diff next time the car comes out.

Still i could try the old boiling water trick and see how close it is as well

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...