Jump to content
SAU Community

Recommended Posts

Hi All,

R33-r34 Turbo, differences??

I have used the search but i cant find anything

Can someone please help?

maybe specs n stuff of the r33 from someone and the specs about the r34 from someone else..

then i can compare..

thanks pplz

Lighty01

PS. Info just about the turbo only

Edited by lighty01
Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/
Share on other sites

sorry matey, but that's incorrect.

r33 turbo = ball bearing.

The sI turbos had a metal compressor wheel.

SII turbos have a bakelite compressor wheel for faster spool

both have ceramic turbines - the limiting factor. Once boost is increased too much, the rear wheel pops.

some r34s had the same turbos as r33s.

The rest have the same turbo but a larger exhaust housing like the vg30 turbo.

I have a large housing avaialble if you need it.

Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/#findComment-3225302
Share on other sites

  • 3 months later...

If the R34 and VG30 have the same exhaust housing does this mean they will perform much the same?

I have a VG30 on my RB20DET and wanted to go to something less laggy. I am ready to buy a R34GTt turbo, though it is clearly not worth my while if there is no difference between the two.

Your thoughts?

Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/#findComment-3457805
Share on other sites

I just bought an R33 Series 2 turbo for my RB20, I was after a 34 one but they are too hard to find and overpriced. But if there's f*ckall diff then i'm glad i've gone the 33 S2. Would putting the larger 34 housing on it be a bad idea and make it more laggy on the RB20?

Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/#findComment-3457960
Share on other sites

KeyMaker,

Are you saying that a R34 GTt turbo would be more laggy than a VG30 turbo or more laggy than an R33 GTSt turbo?

The benefit of the R34 turbo over the R33 is not that it is more power, rather, that it is newer.

Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/#findComment-3457979
Share on other sites

Yes its based on the exhaust housing....primarily.

R34 turbo should be less laggy than a VG30 turbo due to the use of a nylon/plastic impeller. I'm not sure on the specs of a VG30 turbo or what impeller it uses so i'm assuming its a steel impeller. So therefore the R34 turbo has a lighter rotational mass to turn = less lag.

But the R34 turbo shares the same exhaust housing as the VG30 turbo.

If I were you, I'd get a R33 S2 Turbo if you want to reduce lag & and you'll still get the same power, as the compressor housing on the 33 is the same as a 34 turbo and you won't be able to run any more boost than a 34 turbo.

Edited by KeyMaker
Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/#findComment-3458004
Share on other sites

Just on topic..

R33 turbo is laggier and will have less responce than a R34 series one turbo .. R34 series 1 turbo spools much quicker and with the right mods can be full boost a 3g and less.

R34 turbo series 2, is bigger and can run a higher boost level, still spoools quick but not as fast as a series1 .. Ideal for a high flow.

I only know this because ill be doing exactly that for my 34

Link to comment
https://www.sau.com.au/forums/topic/176238-r33-r34-turbo/#findComment-3458191
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...