Jump to content
SAU Community

Recommended Posts

Hey guys, I installed some gauges into the triple gauge cluster of my R34 GT-T a few weeks back, finally got around to taking some proper pics for those interested in how it looks. I got the gauges off Ebay, they are Autogauge brand, smoke series (left to right water temp, oil temp and boost). They work really well and look so much better than the stock ones.

The installation wasnt that hard, took me a couple of hours all up. This is what I did for those who may want to try.

1. Remove aircon vents (simply use a flathead screwdriver to pop them out gently, no screws need to be undone).

(note: i didnt unplug the aircon, i just worked around it)

2. Remove screws holding in cluster and unplug the adaptor plug going into the back of the stock gauges.

3. As you will see, the stock unit is actually a single piece. I disassembled this unit and removed the gauge unit from its casing/holder

4. I retained the stock holder with the glass and mounted the three gauges within the original using some liquid nails and silicon to hold them in place. This was probably the hardest part as you have to be careful not to make a mess of everything.

5. I used a multimeter to figure out which of the wires going into the stock adaptor were for lights, ignition and ground and then cut said wires, splicing them together with their respective counterparts from the gauges.

6. I extended the green wires for the temperature senders (oil temp and water temp) and ran them down through the dash to the drivers side footwell along with some 4mm PVC tubing for the boost gauge which I got from Bunnings. I could not find a suitable firewall to get these through to the engine bay so I ran them around through the drivers side door (It actually doesnt look that bad, I covered them with electrical tape, not noticeable at all).

7. I tested and reassembled the unit and grounded the gauges to a bolt from the aircon. Make sure the gauges are aligned properly before putting everything back together!!

The finished product: (they look awesome at night...heaps better than the stock ones!)

post-23301-1184499833_thumb.jpg

post-23301-1184499856_thumb.jpg

post-23301-1184499876_thumb.jpg

post-23301-1184500059_thumb.jpg

I used 52mm gauges. I've seen this done with 60mm Saber gauges, there was an article in Hot 4s on how to do it, but they stick out of the cluster and require the openings to be cut back a little to fit. I opted for the 52mm gauges as I wanted to keep them behind the glass, looks more professional IMO.

  • 3 weeks later...
Hey Suj, I was wondering did you use a sandwich plate in order to hook up the oil temp gauge

Slow reply but yes I did, purchased it from Just Jap, was about $30. You'll need a new oil filter as well though if you are going to do it. My advice would also be to attach the sensors and extend the wires to them before fitting the new filter/sandwich plate, makes things much much easier when hooking up the gauge

hi guys

i did the same mod awhile back but used silver faced speco gauges and added a shift light, i also wanted to keep the gauges behind the factory glass.

http://www.skylinesaustralia.com/forums/in...e+gauge+cluster

if you want to see pics take a look at the link. for some reason i couldnt upload them again.

  • 2 weeks later...

Hi Suj, great job in the cluster there. However i am trying to fit a profec b into my r34 gtt at the moment, and have found the drivers door wire entry is a one piece plastic plug type arrangment just big enough to fit the hole in the chassis. im trying to find a way to get a vacuume/ boost line and electrical plug into the cabin and found this way has failed. did u open the hole up a little? any info would be appreciated.

Hi Suj, great job in the cluster there. However i am trying to fit a profec b into my r34 gtt at the moment, and have found the drivers door wire entry is a one piece plastic plug type arrangment just big enough to fit the hole in the chassis. im trying to find a way to get a vacuume/ boost line and electrical plug into the cabin and found this way has failed. did u open the hole up a little? any info would be appreciated.

Hey mate sorry for slow reply, been away for a bit.

I actually just ran my tubing through the drivers side door, e.g. not actually through the firewall as I couldn't find a way to get it through. I'll try to get a photo of what I mean soon.

  • 1 year later...
Gauges were off ebay (Autogauge smoke series). Got them for $150 delivered for the three of them.

Just a note as some of you seem to have trouble getting through the firewall if you look down behind the fusebox there is a large grommet where the wiring goes out you can get your wires and boost pipes through these without too much trouble and it has a hole in the inner wing where you can get the wires throught to the engine bay

hope this helps

Don

  • 3 weeks later...

SUJ as per step number 1 when your reffering to removing the air con vents...how exactly do you do that and which part of the air con do you use a flat head screw driver on?? as im confused and not sure where to start...a photo or something would be great.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 2001 BE5D Subaru Legacy B4 RSK (3rd gen) EJ208 (pink injector) Twin Turbo 280PS 5-speed manual Full time 4WD "RSK" grade which means all of the above LQC option which means stock rear spoiler  I got it primarily to export to someone outside Japan who was interested. These BE5 Legacy B4 RSKs are going through a bit of a resurgence right know in Japan as they are one of the few cars from the "turbo, manual, RWD/4WD, 280hp gentleman's agreement era" cars that don't require stupid money to purchase. Which for some people might be a good opportunity to get as a base for restoration. If I can't find anyone to purchase it I will certainly be doing that myself over the long term. Why? Because it's properly fast in stock form, handles well enough for a GT sedan, there's still enough aftermarket and (if you can wait a while) genuine part support to make it a restoration candidate (<-- that will only get worse over time so it's a case of do it now or choose get a BL5 4th Gen). Mechanically it's fine, has only 89,200kms on the odometer. The problem with this car is that the body and exterior trims are weathered from at least the last 10 years being parked outdoors. I'm the 3rd owner, the first owner was the one that had it for 14 years and barely drove it, had a low-speed front impact (which didn't damage anything behind the radiator support) and got it fixed and sold it. The 2nd owner put most of the kms on it and parked it outside for the last 10 years, hence the door rubbers have seen better days but if you overlook those cosmetic details, it presents pretty nicely. There is some minor rust on the LH rear wheel arch which I'll have looked at too at some stage.  Also as you'd expect from a car this age, the clear top coat is gone, leaving a satin finish on the roof.  Mechanically it's fine (as you would expect from a car with less than 100K kms) but the steering does feel slightly vague around the centre position at higher speeds. So first on the list is to get the steering rack bushes looked at. There's also the Lock button on the remote which doesn't work, but the Open button does.... it means that the anti-theft system thinks it's always open? It seems like if you open the car and don't start the engine within 3 mins or so the anti-theft kicks in again without any beeps or signals. So if you got to start it after that, it won't. You have to push the open button again. That's how I understand it anyway. Just a small irritation but not a big problem to sort out. There's only one mod, the Wangan SPL muffler. Just a tad louder than stock. It's a really good mod for those who don't want to wake the neighbours but still want to hear a more prominent unequal length header EJ20 sound. Anyway I hope to get all those things done eventually, that is unless someone wanted to import it to their country from Japan (where I live). I'm open for negotiations as I really would like a Skyline... but this will definitely suffice in the meantime 🙂 *Disclaimer: This is how I picked it up from the dealer, minus the stuff on the back seat. I haven't cleaned the engine bay or done a thorough exterior clean, aside from spray painting the wipers. 
    • Wow, even with the Audi logo centre caps. I love OEM wheel mismatches. 
    • Welcome!  Can't go wrong with a Stag.
    • Looks good. Nice height.
    • Hey all, a little help from the Stagea hive mind plz.. I'm days away from buying either a 2002 Stagea 250tRS AR-X Four, premium leather, power seats and all the old switches etc that go with it, or a 2002 Stagea 250tRS VR-X Four AERO, pov pack, cloth seats etc, with coil overs, sports zorst, comes with original zorst and suspension and parts. (I think I've got the models right?) Both are VQ25DET, have 160000kms, both straight no rust both with $2000+ in recent servicing receipts, both ride on aftermarket 18" rims. The Aero has a replaced turbo as well. I like the cool factor of the Aero car but the AR-X has never been modified. Neither have been driven hardly at all in the last 5 years. Any thoughts on which one or does it come down to personal preference? davemoto 
×
×
  • Create New...