Jump to content
SAU Community

Recommended Posts

r32 rb25de head on the existing rb25 block and transfer all the existing rb20 stuff over to the new head, injectors, manifolds, ignition system etc. except use the rb25 turbo you talking about having.

rb25de head: ~$1000

GT-R valve springs: ~$100

Head Gasket: ~$500

That's assuming the rb25 bottom end is ok

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3240632
Share on other sites

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

How much did you pay for it? $2000?

You get what you pay for buddy, I hope you disclose all this when you go to on-sell the car to some poor unsuspecting person.

Nope.. because the job will be done properly this time.. :banana:

With proper parts.. and tools.. So there is no need to hide it.. the will be done right this time..

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3241686
Share on other sites

Weetbix...........absolutely no taste............Cocoa Pops or Froot Loops at least.

Some shops get customers that bring in a wheelbarrow full of bits and peices and say 'Build me a car!'.

The shop says 'No way', so the moron wheels his barrow to the next shop, eventually someone will say OK.

To be fair, it happens with mod parts as well, some shops will sell you anything, other shops try to tell you what will work and what is a waste of $$$$.

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3242403
Share on other sites

This was taken out from cylinder 1

The diameter of the pison is 85.95mm

The diameter of the bore is 86.05mm (standard bore is 86.0 - somone has been playing with toys they shouldnt of been!)

On the face of the piston is has imprinted "STD" and a big "1" in the middle. Mean anything?

the question I have is..

are these forgies?

What brand?

t938074_IMGP0135CROPPED.JPG

Edited by GTS4WD
Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3242735
Share on other sites

Id say, go and get the bores taken out .5mm over standard. Pretty sure every piston manufacturer has that oversize eg. ACL, Aries, HKS, CP, JE etc etc

Prices are average around 1200-1400 bucks for pistons and rings.

Rebore would be around $300ish

Getting Pistons fitted to Rods - Around $200

Hope you find this useful

Andrew

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3243061
Share on other sites

Id say, go and get the bores taken out .5mm over standard. Pretty sure every piston manufacturer has that oversize eg. ACL, Aries, HKS, CP, JE etc etc

Prices are average around 1200-1400 bucks for pistons and rings.

Rebore would be around $300ish

Getting Pistons fitted to Rods - Around $200

Hope you find this useful

Andrew

Yeah mate.. all bits help.. :)

Can anoyone confrim they are forgies though?

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244478
Share on other sites

This was taken out from cylinder 1

The diameter of the pison is 85.95mm

The diameter of the bore is 86.05mm (standard bore is 86.0 - somone has been playing with toys they shouldnt of been!)

On the face of the piston is has imprinted "STD" and a big "1" in the middle. Mean anything?

the question I have is..

are these forgies?

What brand?

t938074_IMGP0135CROPPED.JPG

It's 0.1mm difference! - you have to have some clearance between the piston and bore. The spec for bore is nominal - there will be some manufacturing variations.
Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244638
Share on other sites

It's 0.1mm difference! - you have to have some clearance between the piston and bore. The spec for bore is nominal - there will be some manufacturing variations.

True.. of MAX .05 (according to the workshop manual)

So the pistons would of been fine if they didnt f*ck around with the bore :) Dodgy deadshits!

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244675
Share on other sites

This was taken out from cylinder 1

The diameter of the pison is 85.95mm

The diameter of the bore is 86.05mm (standard bore is 86.0 - somone has been playing with toys they shouldnt of been!)

On the face of the piston is has imprinted "STD" and a big "1" in the middle. Mean anything?

the question I have is..

are these forgies?

What brand?

t938074_IMGP0135CROPPED.JPG

there defiantly forgies. The piston you have are sold by precision performance. they retail for $1500. they are some chinese brand but dont be to worried there no to bad really. these are mine that we put in rb30's for a cheaper optioned rebuild. Just put it all back together and drive it, as lond as there not damaged it will be sweet. cheers

04102006146.jpg

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244691
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...