Jump to content
SAU Community

Recommended Posts

r32 rb25de head on the existing rb25 block and transfer all the existing rb20 stuff over to the new head, injectors, manifolds, ignition system etc. except use the rb25 turbo you talking about having.

rb25de head: ~$1000

GT-R valve springs: ~$100

Head Gasket: ~$500

That's assuming the rb25 bottom end is ok

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3240632
Share on other sites

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

How much did you pay for it? $2000?

You get what you pay for buddy, I hope you disclose all this when you go to on-sell the car to some poor unsuspecting person.

Nope.. because the job will be done properly this time.. :banana:

With proper parts.. and tools.. So there is no need to hide it.. the will be done right this time..

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3241686
Share on other sites

Weetbix...........absolutely no taste............Cocoa Pops or Froot Loops at least.

Some shops get customers that bring in a wheelbarrow full of bits and peices and say 'Build me a car!'.

The shop says 'No way', so the moron wheels his barrow to the next shop, eventually someone will say OK.

To be fair, it happens with mod parts as well, some shops will sell you anything, other shops try to tell you what will work and what is a waste of $$$$.

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3242403
Share on other sites

This was taken out from cylinder 1

The diameter of the pison is 85.95mm

The diameter of the bore is 86.05mm (standard bore is 86.0 - somone has been playing with toys they shouldnt of been!)

On the face of the piston is has imprinted "STD" and a big "1" in the middle. Mean anything?

the question I have is..

are these forgies?

What brand?

t938074_IMGP0135CROPPED.JPG

Edited by GTS4WD
Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3242735
Share on other sites

Id say, go and get the bores taken out .5mm over standard. Pretty sure every piston manufacturer has that oversize eg. ACL, Aries, HKS, CP, JE etc etc

Prices are average around 1200-1400 bucks for pistons and rings.

Rebore would be around $300ish

Getting Pistons fitted to Rods - Around $200

Hope you find this useful

Andrew

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3243061
Share on other sites

Id say, go and get the bores taken out .5mm over standard. Pretty sure every piston manufacturer has that oversize eg. ACL, Aries, HKS, CP, JE etc etc

Prices are average around 1200-1400 bucks for pistons and rings.

Rebore would be around $300ish

Getting Pistons fitted to Rods - Around $200

Hope you find this useful

Andrew

Yeah mate.. all bits help.. :)

Can anoyone confrim they are forgies though?

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244478
Share on other sites

This was taken out from cylinder 1

The diameter of the pison is 85.95mm

The diameter of the bore is 86.05mm (standard bore is 86.0 - somone has been playing with toys they shouldnt of been!)

On the face of the piston is has imprinted "STD" and a big "1" in the middle. Mean anything?

the question I have is..

are these forgies?

What brand?

t938074_IMGP0135CROPPED.JPG

It's 0.1mm difference! - you have to have some clearance between the piston and bore. The spec for bore is nominal - there will be some manufacturing variations.
Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244638
Share on other sites

It's 0.1mm difference! - you have to have some clearance between the piston and bore. The spec for bore is nominal - there will be some manufacturing variations.

True.. of MAX .05 (according to the workshop manual)

So the pistons would of been fine if they didnt f*ck around with the bore :) Dodgy deadshits!

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244675
Share on other sites

This was taken out from cylinder 1

The diameter of the pison is 85.95mm

The diameter of the bore is 86.05mm (standard bore is 86.0 - somone has been playing with toys they shouldnt of been!)

On the face of the piston is has imprinted "STD" and a big "1" in the middle. Mean anything?

the question I have is..

are these forgies?

What brand?

t938074_IMGP0135CROPPED.JPG

there defiantly forgies. The piston you have are sold by precision performance. they retail for $1500. they are some chinese brand but dont be to worried there no to bad really. these are mine that we put in rb30's for a cheaper optioned rebuild. Just put it all back together and drive it, as lond as there not damaged it will be sweet. cheers

04102006146.jpg

Link to comment
https://www.sau.com.au/forums/topic/177193-dilemma/page/2/#findComment-3244691
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...