Jump to content
SAU Community

Recommended Posts

Hey guys,

For a while now my car has had alignment issues in that the car always pulls left as soon as the wheel is left to itself. Obviously the faster I'm going the more noticeable this pull is. I've had it aligned numerous times and also replaced the front bearings in the hopes that this would fix it. My suspension shop seems to think all my bushes are in order and can't seem to pinpoint my problem.

The worst of it occurs whenever the car is taken above 100kph. The steering wheel starts shaking pretty crazily and makes any sought of trip in a 100 zone a bit annoying as I get jelly arms at the end of it and sore wrists.

From what I've heard elsewhere warped discs might be a contributor but I'd imagine that'd only be the case in a braking situation rather than just driving. I'll be getting new discs/pads soon regardless but I'm interested in any other ideas of what might be causing this.

Control arms maybe?

Any help is greatly appreciated.

Pete

Link to comment
https://www.sau.com.au/forums/topic/177861-alignment-issue/
Share on other sites

Um what are your tyres like?

When I bought my old R33 the tyres that were on it were 'feathered' which caused the steering wheel to vibrate quite bad at speeds above 80km/h or so (felt normal at 60km/h). I dont know much about it but basically the tyres wear unevenly (due to misalignment) and you cant balance them to fix the problem, so although they still had good tread I had to get new tyres which fixed the problem (and an alignment to stop it happening again).

Just something to check. Good luck.

Link to comment
https://www.sau.com.au/forums/topic/177861-alignment-issue/#findComment-3246671
Share on other sites

If the road cambers to the left, then the car will steer left.

Have you ever rotated the wheels so that the wheels swap sides, ie left -> right, right -> left ?

Try swapping the fronts to the back (unless of course you have different width wheels front and rear) to see if the problem persists.

Are the wheels sitting on the hub centring rings? Or sitting on the wheel studs?

Link to comment
https://www.sau.com.au/forums/topic/177861-alignment-issue/#findComment-3246762
Share on other sites

Yeah I've got wider rears than fronts so that options out.

The tyres are brand new as are the rims they're sitting on. They've been balanced and problem persists.

An additional note, whenever the car is hoisted up the problem disappears for a few days before reappearing at a slow pace.

Link to comment
https://www.sau.com.au/forums/topic/177861-alignment-issue/#findComment-3247833
Share on other sites

Aiks! Mine seem to have the same problem but it pulled more to the right and find it harder when turning on long sweeping left hander. But now its getting much more twitchy after installing the Cusco adjustable camber arms (front & rear), Cusco tension rods and Nismo Swaybars.

Alignment check seem ok. Think it could be the bushes?

Link to comment
https://www.sau.com.au/forums/topic/177861-alignment-issue/#findComment-3247945
Share on other sites

I would love to find out the cause of this problem. I am still running the crappy 225*50*16 compliance tyres that my car came with so it may be due to shitty tyres. Above around 130kph it gets bad bad scary vibration and also pulls to the left but not badly. The shock is transmitted through the steering wheel but dosent seem to affect the cabin which is strange.

Link to comment
https://www.sau.com.au/forums/topic/177861-alignment-issue/#findComment-3251052
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...