Jump to content
SAU Community

Ordering Of Sau Hoodie For Sa And Other States

jugz

By jugz,
in South Australia

 Share

Recommended Posts

Madaz Grand Master

Madaz

Posted
Posted

i would like to change my size

Size XL 120 to fit chest 107 this is what is on my work jumper and it fits well

is it possible to get samples and have a dinner in the city one night maybe aussie pizza house hutt st

most these places should have jumpers they can send out fo you to try

Madaz Grand Master

Madaz

Posted
Posted

na i wont want one before auto salon prolly wont even go but not sure

would still like a first hand look @ some sample clothing

being a manufacturer of a different product i know they must have seconds that they give to prospective buyers

Kroozin Enthusiast

Kroozin

Posted
Posted
ok need to know this asap

how many people really really want a jumper before autosalon????????

If it is possible yes, cos I will be helping with the setup on Friday.

Can I also change my size to medium, zipped with nick name: Kroozin

  • 3 weeks later...
MissR34 Grand Master

MissR34

Posted
Posted

Hey everyone,

the lady that i have been speaking to about the jumpers will be able to do them after september 7. i know its a long time but she is going interstate.

now i have asked to get some samples, and hopefully i might be able to bring them to the cruise on sunday.

will let you know.

cara

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...