Jump to content
SAU Community

Recommended Posts

Your injectors can clog up due to bad fuel but I dont know about them physically breaking because it.

I only ever use BP Ultimate, or if I cant get BP I use Mobil Synergy and have never had a problem with either of them, I have used Caltex and Shell in the past but my engine didnt like them as much (especially shell), I got less Km's from a tank and it felt sluggish and unresponsive, the engine pinged few times at high revs while using Shell.

I have a bit of a bias opinion though, my car has a Power FC computer and 550cc injectors (along with some other goodies) and it was dyno tuned using BP Ultimate.

Link to comment
https://www.sau.com.au/forums/topic/180964-fuel-type/#findComment-3288856
Share on other sites

Agree with Bullet. I make special trips into canberra for BP Ultimate :) and if i cant get that then Mobil 8000. There was some testing done (am looking for the post on the forums) of the major petrol companies (BP, Shell, Mobil, Caltex) to show the RON of their high performance petrols and BP, Mobil and Shell came out on top with 98s and 97s, think vortex was around 95

Skylines should only be run on a minimum of 95 RON

Edited by Baconer
Link to comment
https://www.sau.com.au/forums/topic/180964-fuel-type/#findComment-3288888
Share on other sites

I could be wrong, but I believe Mobil actually uses BP Ultimate for its Synergy8000, but makes its own other fuels. This is just a rumour and I have nothing to back it up, except that they are coincidently both excelent fuels.

Link to comment
https://www.sau.com.au/forums/topic/180964-fuel-type/#findComment-3289242
Share on other sites

fuel injectors can be harmed by wrong fuel, I have no proof but there are additives in some fuel that will eat the rubber out on some older cars!!!

Stick with most 98 ron stuff and you will be fine, BP and Caltex for the win

Link to comment
https://www.sau.com.au/forums/topic/180964-fuel-type/#findComment-3289583
Share on other sites

they all do the same thing. only changes when the octane changes. my car runs the same on all the 98 octane fuels. notice a big difference when i use the V-power racing, which is 100+ octane....

Incorrect... Remember that your car still has standard injectors, standard fuel pump and standard computer, when you replace all these for after market / higher flowing items and you have it much more hard tuned than factory you find that the engine becomes very picky about what you put into it.

Mine ran very bad on Shell and almost as bad on Caltex but BP and Mobil are great, so thats enough evidence for me.

Link to comment
https://www.sau.com.au/forums/topic/180964-fuel-type/#findComment-3291376
Share on other sites

i dont think that shell optimax (yes i'm still old school) is too bad.

haha I went to a shell the other week for the first time in ages (cos I had to) & was looking for the blue pumps... couldnt work out WTF was going on :D

but yeah, i always use BP normally :O

Link to comment
https://www.sau.com.au/forums/topic/180964-fuel-type/#findComment-3306963
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...