Jump to content
SAU Community

Nistune

Crans

By Crans,
in Engines & Forced Induction

 Share

Recommended Posts

BXAFTW Community Regular

BXAFTW

Posted
Posted

just read the entire thread, and this sounds like exactly what im after.

so can these chips be installed into an r34gtt ecu? do you nistune guys know of any tuners in tasmania who can tune your stuff?

how much for a chip fited to my ecu? ready to be tuned, or any other options?

cheers

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5071256
Share on other sites
  • Replies 377
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkhalf
darkhalf

Guys it was my bad about the information provided to the workshop mentioned in this thread with regards to compatibility since I mixed up the model numbers. Usually I refer to the Nissan vehicle desig

Artic Choc
Artic Choc

yeah ive seen many cases where engine protection has stopped or at lest reduced damage to engines.. if your paying top dollar for an ecu youve probably got alot of cash sunk into your engine too.. it

Posted Images

darkhalf Community Regular

darkhalf

Posted
Posted

Prices and details are on the website, I'm getting the website updated soon to quote people on everything...

R34 GTT - Type 4 board $260, installation $60, postage $15 + GST = $335

Call around Tassie and see who is willing to tune it since we dont have anyone listed there yet. I know a few people there have gotten tuned using their licence but no one has signed up as a workshop. Most workshops have signed up after using the system as we dont advertise in managzines etc its been mainly word of mouth... internet helps too!

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5071381
Share on other sites
XRATED Veteran

XRATED

Posted
Posted
just read the entire thread, and this sounds like exactly what im after.

so can these chips be installed into an r34gtt ecu? do you nistune guys know of any tuners in tasmania who can tune your stuff?

how much for a chip fited to my ecu? ready to be tuned, or any other options?

cheers

Contact SPG- Nick Summers pushes out some great tunes.

Also Mobile Mechanics- Martin is handling my install.

Both in Hobart/Moonah.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5074431
Share on other sites
  • 3 weeks later...
427 Collaborator

427

Posted
Posted (edited)

hi mates,

i've got ecr 33 rb25det with auto transmisson

could you pls advise what ECU+nistune is suitable for my car?

i know z32 and r32 ECUs are ok but what kind (turbo, non turbo, Auto transmission or manual)?

also - how will i tune my car if i will install nistune? for example when i add some modifucations, as FMIC, what should i do with Nistune?

Edited by 427
Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5108936
Share on other sites
  • 1 month later...
STATUS Grand Master

STATUS

Posted
Posted
hi mates,

i've got ecr 33 rb25det with auto transmisson

could you pls advise what ECU+nistune is suitable for my car?

i know z32 and r32 ECUs are ok but what kind (turbo, non turbo, Auto transmission or manual)?

also - how will i tune my car if i will install nistune? for example when i add some modifications, as FMIC, what should i do with Nistune?

I prefer to use the later Z32 ecu's but main concern is to get a turbo auto ecu as a manual one will give you shift inconsistency's.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5153952
Share on other sites
QWK32 Veteran

QWK32

Posted
Posted
Can a nistune tunner explain to me how the latency settings work? It shows the values in (us) ever time I look at it my head starts to spin.

nistune uses "us" or micro-seconds to measure injector latencies. as most injector latencies are given as milli-seconds you need to convert it. ms * 1000 = us

so an injector with a 0.7 ms latency, is inputted into nistune as 700 us. an injector with a 1.3 ms latency is inputted as 1300 us.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5154242
Share on other sites
QWK32 Veteran

QWK32

Posted
Posted
is there nistune software for a MAC computer?

software designed for mac, no. but, you can run nistune through a Windows VM with a program like Parallels, it runs fine this way. thats how i've been running nistune at the moment, until i get an old windows laptop i have up and running.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5154283
Share on other sites
STATUS Grand Master

STATUS

Posted
Posted
Has anyone tryed running blow through with the ford lightning maf meter?? And can nistune support injectors as big as 800cc's or so?

I have used blow through on a few cars (requires alot of work in the AFM voltage table) and 1000cc injectors on E85 without issues.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5154794
Share on other sites
BlueRB240 Collaborator

BlueRB240

Posted
Posted
nistune uses "us" or micro-seconds to measure injector latencies. as most injector latencies are given as milli-seconds you need to convert it. ms * 1000 = us

so an injector with a 0.7 ms latency, is inputted into nistune as 700 us. an injector with a 1.3 ms latency is inputted as 1300 us.

Wow thanks that clears it up a lot for me.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/10/#findComment-5155793
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      I like their veal scallopini.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Definitely a hearty eater when we go out, I consider these meals my cheat day as I've been watching my calories in and calories out pretty hard since my little fun size stroke, I've gone from a fat boy of 89 Kg, I'm only 165cm tall/short, down to a almost semi lean 73 Kg over the last few years, I'm currently around 17% body fat which my doctor is very happy with, but, my goal is to slowly get down to and maintain 15%,so yeah, I want all of the protein, carbs, fats and sugars when I go out for a binge
    • Duncan
      NC MX5

      By Duncan · Posted

      There was a great one on Victoria Rd in Gladesville too back in the day. I can only assume GTSBoy is thinking of the mill up on the wollondilly, no restaurant there any more but they have restored the original steam engine on site and run it every few months, have an annual steampunk festival etc @The Bogan, you came to the wrong town for restaurants. we have a few reasonable asian and indian options but the Paragon is as good as it gets otherwise. That brewery is apparently just opened, been meaning to give it a go some time. The Highlands have plenty of fancy options but I suspect you are more a hearty eater than fancy eater
    • Duncan
      Squeaking clutch/throw out bearing

      By Duncan · Posted

      Thanks for coming back to post the update, maybe it will help out the next person!
    • WMDC35
      Engine model

      By WMDC35 · Posted

      Going by the intake & injectors I'd be guessing it's a DE, check the head casting number, should be 5L8 on a DET, 5L7 I think is the DE number.
×
×
  • Create New...