Jump to content
SAU Community

Nistune


Crans

Recommended Posts

just read the entire thread, and this sounds like exactly what im after.

so can these chips be installed into an r34gtt ecu? do you nistune guys know of any tuners in tasmania who can tune your stuff?

how much for a chip fited to my ecu? ready to be tuned, or any other options?

cheers

Link to comment
Share on other sites

Prices and details are on the website, I'm getting the website updated soon to quote people on everything...

R34 GTT - Type 4 board $260, installation $60, postage $15 + GST = $335

Call around Tassie and see who is willing to tune it since we dont have anyone listed there yet. I know a few people there have gotten tuned using their licence but no one has signed up as a workshop. Most workshops have signed up after using the system as we dont advertise in managzines etc its been mainly word of mouth... internet helps too!

Link to comment
Share on other sites

just read the entire thread, and this sounds like exactly what im after.

so can these chips be installed into an r34gtt ecu? do you nistune guys know of any tuners in tasmania who can tune your stuff?

how much for a chip fited to my ecu? ready to be tuned, or any other options?

cheers

Contact SPG- Nick Summers pushes out some great tunes.

Also Mobile Mechanics- Martin is handling my install.

Both in Hobart/Moonah.

Link to comment
Share on other sites

  • 3 weeks later...

hi mates,

i've got ecr 33 rb25det with auto transmisson

could you pls advise what ECU+nistune is suitable for my car?

i know z32 and r32 ECUs are ok but what kind (turbo, non turbo, Auto transmission or manual)?

also - how will i tune my car if i will install nistune? for example when i add some modifucations, as FMIC, what should i do with Nistune?

Edited by 427
Link to comment
Share on other sites

  • 1 month later...
hi mates,

i've got ecr 33 rb25det with auto transmisson

could you pls advise what ECU+nistune is suitable for my car?

i know z32 and r32 ECUs are ok but what kind (turbo, non turbo, Auto transmission or manual)?

also - how will i tune my car if i will install nistune? for example when i add some modifications, as FMIC, what should i do with Nistune?

I prefer to use the later Z32 ecu's but main concern is to get a turbo auto ecu as a manual one will give you shift inconsistency's.

Link to comment
Share on other sites

Can a nistune tunner explain to me how the latency settings work? It shows the values in (us) ever time I look at it my head starts to spin.

nistune uses "us" or micro-seconds to measure injector latencies. as most injector latencies are given as milli-seconds you need to convert it. ms * 1000 = us

so an injector with a 0.7 ms latency, is inputted into nistune as 700 us. an injector with a 1.3 ms latency is inputted as 1300 us.

Link to comment
Share on other sites

is there nistune software for a MAC computer?

software designed for mac, no. but, you can run nistune through a Windows VM with a program like Parallels, it runs fine this way. thats how i've been running nistune at the moment, until i get an old windows laptop i have up and running.

Link to comment
Share on other sites

I imagine you could run it via a virtual machine running xp/vista/w7. Virtual box is a great program, you could install XP in this, map your USB ports to the virtual machine and then run the software this way.

Link to comment
Share on other sites

Has anyone tryed running blow through with the ford lightning maf meter?? And can nistune support injectors as big as 800cc's or so?

I have used blow through on a few cars (requires alot of work in the AFM voltage table) and 1000cc injectors on E85 without issues.

Link to comment
Share on other sites

nistune uses "us" or micro-seconds to measure injector latencies. as most injector latencies are given as milli-seconds you need to convert it. ms * 1000 = us

so an injector with a 0.7 ms latency, is inputted into nistune as 700 us. an injector with a 1.3 ms latency is inputted as 1300 us.

Wow thanks that clears it up a lot for me.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Go to SP mufflers and get the muffler of size you want and make a nice mid muffler. It's about that simple! I have 2x 3.5 Magnaflow straight through Mufflers and while it's pretty loud with the Varex open, it's quiet enough with the Varex closed. You can also buy off the shelf Magnaflow straight through mufflers as well. You also have a turbo to quiet the car down too. Don't overthink it. Buy my extra Magnaflow muffler sitting on a shelf doing nothing (buy it new, ignore this part)
    • Centre-offset muffler under the floor, same as stock. Just....3.5". The change from straight pipe there to centre-offset will mean that you need to remake some of the pipe (add a bend or two).
    • Hey guys. So my R34 GTT has a custom 3.5” exhaust (done by previous owner) with a high flowing cat, and then just a Varex cannon muffler on the back. The car does drone alot and is really loud even on highway driving just cruising, as you can imagine due to the Varex muffler basically being a straight through with the valve open. As much as i love a loud RB, it can be a bit much with no other muffling in line and just driving casually. I wanted to lower the volume output on the exhaust a bit, as well as remove the drone (probably a way to do both at once), and was going to do it all myself as I am a fabricator and have done exhaust work in the past, so the fab work isnt my issue, im just not sure on the right product or type of product to use to get the job done, and i doubt an exhaust shop would be wanting to help me as they wont be making any money from helping me, unless they supplied the product? Anyway any help or guidance in best way to approach this would be awesome   Thanks in advance
    • Meh, whilst the Honda is a "really" good car and has potential if you want to drop coin on, it was uninspiring for me to look at, but, it did serve its purpose and is now in the boys hands, his happy, his girl is happy, as she wasn't to keen on the noisy old Patrol, and most importantly, the Minister for War and Finances is extremely happy that her "little baby boy" (6'2 nugget who is currently training to be a copper, which will make 3 coppers in the immediate "circle of trust") has a well sorted reliable car that doesn't guzzle diesel Me, I'm more than happy with the NC MX5 that I replaced it with, it's a fun little car that I like looking at, like driving, and yes..... I do like the fact that the maintenance and modifications that I have done/will do are plentiful and relatively cheap, well........ while staying naturally aspirated slow that is, and that's all I really need for a fun little daily, I can rev the 5hit out of it rowing through the gears and never really break the speed limit  In saying that wicked word, "modifications", I've already ordered something for some noise and an additional "3 ish" horse powers, or whatever it gives, in the form of a header, and, a new set of "cheapo" BC coilovers that are already sitting in the shed waiting to get put in, I had the same BC's in my old NB and found they were fine for the street, hwy, and the occasional track days I did in it, they have 6kg front and 4kg rear springs which is about 10% stiffer than the stock springs which I found worked well for their price  I've also already been in touch with MX5 Mania in Dural, so once the header is on it will get a ECUTek RaceROM tune there (I cannot rev match for 5hit, and I loved the RaceROM rev match and FFS in my old 86 "RIP") In other, maintenance news, I put some new sparkler plugs in it, and have a new set of DBA Street series pads to put in over the next day or so, I'm running the DBA street series in the SS and Honda and really like them, they work great and are not dusty at all I've also booked in a few days leave over this weekend to give me 4 days weekend do some paint correction and give the leather seats some conditioning and interior some Bissell and steam cleaning OCD lovin', the carpet and interior looks clean, but from my experience with the Bissell IRT carpet, and the steam cleaner IRT trim, looks can be deceiving I've also found that finding a detachable hard top is proving problematic, the main reason why I didn't like the NC initially was the power retractable hard top that I seen them with gave the roof line a weird look, the detachable roof though looks good, and is a same shape as a NA/NB hard top, similar, but unfortunately not the same as it has different fixture point on the front, so fitting a easy to get NA/NB detachable hard top is no bueno New Old cars are fun, cleaning, hunting and playing around brings much joy How are your beasties going? Do you still have the Skyline with the LS???, or Barra??? that you were playing with
×
×
  • Create New...