Jump to content
SAU Community

Recommended Posts

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

A& B MOTORSPORTS

DYNO DAY

WHEN: 6TH OCTOBER

TIME: 4PM TILL LATE

LOCATION: 41 WINBOUNRE RD BROKVALE 2100

COST: $35 PRE ENTRY (29TH September) $50 ENTRY AFTER THE 30TH

1ST: $600 VOUCHER FOR ANY OF A&B MOTORSPORTS PRODUCTS

2ND: $300 VOUCHER FOR ANY OF A&B MOTORSPORTS PRODUCTS

3RD: $150 VOUCHER FOR ANY OF A&B MOTORSPORTS PRODUCTS

RULES

THERE ARE NO RULES MOST HP WINS UNLIMITED BOOST AND

UNLIMITED NITRIOUS

REQUIREMENTS

CARS MUST BE WARMED UP AND READY TO GO .CARS MUST ALSO

HAVE GOOD TREAD ON THE TYRES

CONTACTS

PAUL: 0410 460 346

WORKSHOP: 99059523

Edited by craked
name down now, pay on the day? $35?

or do u need pre-payment for that?

pre payment needs to be paid for before the 30th september to do so please call paul 0410 460 346 or workshop on 99059523 and ask for paul

what are A&B motorsports products?? please list

please go to aandbmotorsports.com for the list

i see you guys sell booster kits: http://aandbmotorsports.com/boostkit.html

do you guys actually believe they work?

we put a few on the dyno with before and after reading they make adout 5-10hp more

im so in. but what time is late cos i have baseball on that arvo. plus i know atleast 15 cars that will run aswell

all depends on the turn out but hope fully into the early hours of sunday morning




  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...