Jump to content
SAU Community

Two.06l Update (twoogle)

Swiper the Fox

By Swiper the Fox,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 682
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Swiper the Fox Grand Master

Swiper the Fox

Posted
  • Author
Posted (edited)

the GT-RS graph is in 3rd gear so no direct comparson available which is a little disapointing. When i get the 4WD sorted ill take it up for a 3rd gear 4wd run as im just as interested as you Steve-o. The 3rd gear run in rwd just fry's the tyres.

ashamed of high-flow lag...never. Im totally aware of what im doing and know exactly whats needed. Yes ill have knocked a large hole in my torque curve...but that was expected. Peak torque at 7000rpm is whats needed to run the numbers at the strip not 4500rpm like before.

Wayne is going to rescale the graph for me...as soon as he calls me ill go and pick it up.

Edited by DiRTgarage
Bullet32 Veteran

Bullet32

Posted
Posted
the GT-RS graph is in 3rd gear so no direct comparson available which is a little disapointing. When i get the 4WD sorted ill take it up for a 3rd gear 4wd run as im just as interested as you Steve-o. The 3rd gear run in rwd just fry's the tyres.

Ok so obviously still no 4wd... So did you find out if the problem was what you thought it would be Paul?

N1GTR Grand Master

N1GTR

Posted
Posted
would be interesting to see a side by side of your GT-RS graph vs his GT-RS graph.

Yeah would be, but Paul will have higher numbers i suspect due to cams and porting differences. Mine would probably bring them on faster with greater torque. Time will tell :D And its getting the fuel system done right now, so the tune isnt far off

the GT-RS graph is in 3rd gear so no direct comparson available which is a little disapointing. When i get the 4WD sorted ill take it up for a 3rd gear 4wd run as im just as interested as you Steve-o. The 3rd gear run in rwd just fry's the tyres.

ashamed of high-flow lag...never. Im totally aware of what im doing and know exactly whats needed. Yes ill have knocked a large hole in my torque curve...but that was expected. Peak torque at 7000rpm is whats needed to run the numbers at the strip not 4500rpm like before.

Wayne is going to rescale the graph for me...as soon as he calls me ill go and pick it up.

Cool :thumbsup:

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted
He still plays with carby's and pushrod engines...i think i don't need to say anymore.

nah he is really into his Wolf V500 ecu's.. he loved them to death. Wayne is getting really good with aftermarket ecu's now.

He has actually sold quite a few / installed and tuned himself. They are doing really well over there now.

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

The Dirt man has been admitted to hospital :D I hope its not too serious but I will keep everyone updated as soon as i hear anything :) I just rang him to tell him I finally uploaded a video but Stace answered the phone to tell me the bad news :)

Its not because of the reason he was sick last time either. This is un-related.

Here is the video. anyways... Hope you get well soon Paul

Video is still new - should be up soon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
×
×
  • Create New...