Jump to content
SAU Community

Recommended Posts

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

It only does it on the 33s :D they have a clear plastic panel

you can do it on the 32s, but you'd need to cut out the skyline lettering and replace it with a light in behind it and perspex

or create a custom EL one

I'd go for the custom EL one :P

some R32's were sold with a factory EL lightup panels on the back, which were stuck on top of the bumper (over where the factory one is embossed). you can mod it with LED's (as most of the EL sheets are f**ked now after 12 years of use).

here's mine:

from factory:

n669476048_448327_3247.jpg

n669476048_448328_3675.jpg

modded:

lit_up_arse.gif

you gotta buy the panel though, and they're as rare as rocking horse shit.

wire comes up from under the car, there's a rubber grommet under your spare wheel where the wire comes thru. yours probably dosen't light up for the same reason as mine which was the EL's busted after more than 10 years of use.

hot air gun (or hair dryer) the glue between the panel and bumper and slowly use a blade to cut the double sided tape off. Be careful when taking the panel off, its really brittle and can snap in two very easily. Once its off, mod it with a new EL sheet or high brightness LED's and reattach it back on.

some R32's were sold with a factory EL lightup panels on the back, which were stuck on top of the bumper (over where the factory one is embossed). you can mod it with LED's (as most of the EL sheets are f**ked now after 12 years of use).

here's mine:

from factory:

n669476048_448327_3247.jpg

n669476048_448328_3675.jpg

modded:

lit_up_arse.gif

you gotta buy the panel though, and they're as rare as rocking horse shit.

That is incredibly hot, sell it to me!

  • 2 weeks later...

i made a thing up like this for my 180 years back after i saw a GT starlet with a factory one. i was going to do it to my 33 but was too lazy. just make sure the light is either green or red (preferably red) or you may get shafted by the cops. making it blue will definately get you attention from the cops.

i made a thing up like this for my 180 years back after i saw a GT starlet with a factory one. i was going to do it to my 33 but was too lazy. just make sure the light is either green or red (preferably red) or you may get shafted by the cops. making it blue will definately get you attention from the cops.

Dont know about other states but in Tassie you cant have blue or red as they are the emergency colours :rolleyes:

I got pinged for having green strobes (would light up a solid ring around the wheel whilst moving) on my old gixer a couple of years ago :)

Speaking of the panels though there were a couple on EBay the other week so i would keep your eyes on there if you dont want to mod your own :(

  • 1 month later...

funkymonkey that looks off the hook man! really good, i have a r33 s1 so it has the clear 'skyline' @ the back you think it is easy to do this mod?? PM me if you have the time, i have seen the tutorial.

  • 5 weeks later...

There is another DIY somewhere about this, I saw it yesterday. On the R33 S1, cover the letters with masking tape, then spray the rest of the panel the colour of the car. Then insert LEDs behind each letter so that when it is turned on, the letters glow. You can then hook it up to either a switch, your lights, or your brake light. I was thinking about doing this, and was going to hook it up to my lights so that its on all the time during at night, and to the brakes so its on sometimes during the day. Let people know what your rolling in!!

MLT15E does them too, he actually has a thing going, I just do it for myself and friends :)

Though if you are in Syd, and can pick it up, you're friend enough :)

Anyway, should a thread like this, asking a bunch of questions, be in the fabrication section?

Not yet, but it is possible, but would require time, and some very precise cutting... If you can find one of the OEM ones, even if it is broken, I dare say I can work with that, the only thing I am worried about is the cutting really... though i could get that done proffesionally...

MLT15E does them too, he actually has a thing going, I just do it for myself and friends :)

Though if you are in Syd, and can pick it up, you're friend enough :)

Anyway, should a thread like this, asking a bunch of questions, be in the fabrication section?

He's good at it but don't expect overnight delivery :whistling:

Hey man, I burnt the shit out of my hand for you!

I STILL have a f**ked up finger...

Plus there was no real rush, then I got screwed in parts...

wait... YOU HAVEN'T EVEN PAID FOR IT YET! :whistling:

  • 1 month later...
Hey man, I burnt the shit out of my hand for you!

I STILL have a f**ked up finger...

Plus there was no real rush, then I got screwed in parts...

wait... YOU HAVEN'T EVEN PAID FOR IT YET! :D

You gotta love guys you do a favour for than get smart cause it was late. Every one want's something for free don't they!

I think it also looks like a great mod! I'm going to look into it a bit more. Doesn't look to difficult. Hope your finger gets better! You are a Dr anyway so you should be fine. lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...