Jump to content
SAU Community

Recommended Posts

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

It only does it on the 33s :D they have a clear plastic panel

you can do it on the 32s, but you'd need to cut out the skyline lettering and replace it with a light in behind it and perspex

or create a custom EL one

I'd go for the custom EL one :P

some R32's were sold with a factory EL lightup panels on the back, which were stuck on top of the bumper (over where the factory one is embossed). you can mod it with LED's (as most of the EL sheets are f**ked now after 12 years of use).

here's mine:

from factory:

n669476048_448327_3247.jpg

n669476048_448328_3675.jpg

modded:

lit_up_arse.gif

you gotta buy the panel though, and they're as rare as rocking horse shit.

wire comes up from under the car, there's a rubber grommet under your spare wheel where the wire comes thru. yours probably dosen't light up for the same reason as mine which was the EL's busted after more than 10 years of use.

hot air gun (or hair dryer) the glue between the panel and bumper and slowly use a blade to cut the double sided tape off. Be careful when taking the panel off, its really brittle and can snap in two very easily. Once its off, mod it with a new EL sheet or high brightness LED's and reattach it back on.

some R32's were sold with a factory EL lightup panels on the back, which were stuck on top of the bumper (over where the factory one is embossed). you can mod it with LED's (as most of the EL sheets are f**ked now after 12 years of use).

here's mine:

from factory:

n669476048_448327_3247.jpg

n669476048_448328_3675.jpg

modded:

lit_up_arse.gif

you gotta buy the panel though, and they're as rare as rocking horse shit.

That is incredibly hot, sell it to me!

  • 2 weeks later...

i made a thing up like this for my 180 years back after i saw a GT starlet with a factory one. i was going to do it to my 33 but was too lazy. just make sure the light is either green or red (preferably red) or you may get shafted by the cops. making it blue will definately get you attention from the cops.

i made a thing up like this for my 180 years back after i saw a GT starlet with a factory one. i was going to do it to my 33 but was too lazy. just make sure the light is either green or red (preferably red) or you may get shafted by the cops. making it blue will definately get you attention from the cops.

Dont know about other states but in Tassie you cant have blue or red as they are the emergency colours :rolleyes:

I got pinged for having green strobes (would light up a solid ring around the wheel whilst moving) on my old gixer a couple of years ago :)

Speaking of the panels though there were a couple on EBay the other week so i would keep your eyes on there if you dont want to mod your own :(

  • 1 month later...

funkymonkey that looks off the hook man! really good, i have a r33 s1 so it has the clear 'skyline' @ the back you think it is easy to do this mod?? PM me if you have the time, i have seen the tutorial.

  • 5 weeks later...

There is another DIY somewhere about this, I saw it yesterday. On the R33 S1, cover the letters with masking tape, then spray the rest of the panel the colour of the car. Then insert LEDs behind each letter so that when it is turned on, the letters glow. You can then hook it up to either a switch, your lights, or your brake light. I was thinking about doing this, and was going to hook it up to my lights so that its on all the time during at night, and to the brakes so its on sometimes during the day. Let people know what your rolling in!!

MLT15E does them too, he actually has a thing going, I just do it for myself and friends :)

Though if you are in Syd, and can pick it up, you're friend enough :)

Anyway, should a thread like this, asking a bunch of questions, be in the fabrication section?

Not yet, but it is possible, but would require time, and some very precise cutting... If you can find one of the OEM ones, even if it is broken, I dare say I can work with that, the only thing I am worried about is the cutting really... though i could get that done proffesionally...

MLT15E does them too, he actually has a thing going, I just do it for myself and friends :)

Though if you are in Syd, and can pick it up, you're friend enough :)

Anyway, should a thread like this, asking a bunch of questions, be in the fabrication section?

He's good at it but don't expect overnight delivery :whistling:

Hey man, I burnt the shit out of my hand for you!

I STILL have a f**ked up finger...

Plus there was no real rush, then I got screwed in parts...

wait... YOU HAVEN'T EVEN PAID FOR IT YET! :whistling:

  • 1 month later...
Hey man, I burnt the shit out of my hand for you!

I STILL have a f**ked up finger...

Plus there was no real rush, then I got screwed in parts...

wait... YOU HAVEN'T EVEN PAID FOR IT YET! :D

You gotta love guys you do a favour for than get smart cause it was late. Every one want's something for free don't they!

I think it also looks like a great mod! I'm going to look into it a bit more. Doesn't look to difficult. Hope your finger gets better! You are a Dr anyway so you should be fine. lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...