Jump to content
SAU Community

Recommended Posts

There's a heap of fake sard regs around so be careful. I'm using an SX reg and it's been fine.

Rising rate regs usually increase the fuel pressure double the boost so you could be up there, do you have a gauge in the dash?

I don't have a gauge in the cabin, just one on top of the reg, so it's hard to tell what happens under boost conditions.I may buy a sensor to add to my AFR display.

However, I thought that most rising rate regs increased pressure at 1:1 ratio to counteract the boost. That would be the easiest to manufacture as well, with the hose simply adding boost pressure to the diaphram. All the rising rate regs that have a higher ratio than 1:1 seem to be much more expensive & would probably advertise the fact that they have this feature.

Has anyone seen a gauge pod for an M35 at all? I'd really like a double din unit for my stereo/gps but don't want to lose the factory gauges.

How handy are you at making stuff? There's plenty of good ideas out there, but I've not seen anything decent that you can buy straight up, besides the standard A-pillar mounted gauge pods that look a little out of place in a M35, IMO.

Do you just want to relocate the single DIN factory gauges? If you don't have the Nav DVD ROM in the flip up section they will fit there nicely.

How handy are you at making stuff? There's plenty of good ideas out there, but I've not seen anything decent that you can buy straight up, besides the standard A-pillar mounted gauge pods that look a little out of place in a M35, IMO.

Do you just want to relocate the single DIN factory gauges? If you don't have the Nav DVD ROM in the flip up section they will fit there nicely.

Yeah that is exactly what I'm thinking of. Relocate them to where the factory screen is usually located in some sort of pod, then have a double din unit down under the climate control.

Half tempted to try and make something up but if there is interest for others to do this maybe I'm better off trying to organise a group buy of sorts..

Is the factory boost gauge accurate?

Only real reason I want that is to make sure that it's not boosting off it's face - I find the battery charge gauge handy.. front wheel torque isn't necessary although it is a bit of a game. :)

I don't really need anything, but I just don't want to get rid of the standard gauges unless I'm replacing it with something and if it gets replaced I want it to look as standard as possible.

I think it's fairly accurate, but it's only 1bar (14.5 PSI)... :whistling:

Depends on what you're planning on doing to the car, whether you'd need stuff like oil temp, oil pressure, fuel pressure, etc.

Does anyone know if all AR-X's come with the fixtures to buy and install the grate separating the backseats from the boot ie to stop my bloody dog from jumping over. From the pictures that have been sent to me it doesn't look like my AR-X has it standard.

If yes, does anyone want to sell me one.

For those of you who have imported through a broker, how close has been your quoted L&C price compared to the actual final price. My broker has been really excellent but it looks like he's $1500 off what he quoted me or rather what I quoted him as my budget. It's a bit concerning but to his credit he's looking into it for me rather than brushing me off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...