Jump to content
SAU Community

Recommended Posts

excelent. cos i find on sweeping corners it just frys the rears and the inner front. chopping out tyres real fast. so really if it reduces wheelspin on the track it would pay for itsself in using less tyres :mellow:

excelent. cos i find on sweeping corners it just frys the rears and the inner front. chopping out tyres real fast. so really if it reduces wheelspin on the track it would pay for itsself in using less tyres :mellow:

yes, correct it does help even up tyre wear

when we are launching from a start line, our car use to most times only spin one front wheel, now its all four in a blaze of glory!! :(

russ

Edited by giant
Is there any real advantage to a carbon LSD like ATS make that justifies the difference in price?

well I think the big advantage is you get to tell people you have a carbon diff. but unless they are going to remove your engine and sump and check you can do that anyway and no one will know the difference.

to be honest I don't think it's really necessary. In theory the carbon disks should have some better properties and perhaps they last longer but in reality I don't know how much better (if at all) they are. I've used a carbon clutch and it was great but i'm not tossing my convential clutch in the bin to get one. Cusco diffs are cheap at around $1000 mark and perform very well.

well I think the big advantage is you get to tell people you have a carbon diff. but unless they are going to remove your engine and sump and check you can do that anyway and no one will know the difference.

to be honest I don't think it's really necessary. In theory the carbon disks should have some better properties and perhaps they last longer but in reality I don't know how much better (if at all) they are. I've used a carbon clutch and it was great but i'm not tossing my convential clutch in the bin to get one. Cusco diffs are cheap at around $1000 mark and perform very well.

I thought as much. I had heard carbon clutches need a lot of heat to work well so weren't suited to drag racing. I thought there may be some benefit in that for circuit work but wasn't really sure as I haven't actually heard of anyone using one. Maybe useful for chasing 0.001 seconds a lap when everything else is exhausted but unjustified for everyone else.

I can't really comment on the carbon lsd because I've not used a normal plate front lsd. I've used Kaaz and ATS. The Kaaz rear lsd in the honda is noisy but it's been overtighten. The front ats in the gtr is perfectly quiet after the break in process.

Does your make any noise on reverse Russ and what diff are you using in the rear?

  • 2 weeks later...

Good thread guys - great info.

I busted my front spider gears at the recent Dutton VIC on a launch and turn incident on the long wang @ DECA, so i've got a Nismo 1.5 way front LSD going in this week. The Nismo was slightly better priced than the others and came with gaskets / bearings too where the others didn't seem to.

The Z-tune has the 1.5 way, so I thought it would be ok. I guess i'll be able to give a progress report soon, but.....

I'm told that the ATS 1.5 way front diff was apparently a case of rip the steering wheel from your hand when mounting ripple strips etc, so what we actually intend to do is soften off the 1.5 way Nismo, so that it reacts more like a 1 way. Anyway my thinking was more aimed at replacing the sucker as to increase the strenght over a stock unit, because missing out on 9 events while driving back to melbourne and back again wasn't all that fun.

I'll report back what I think of it on the track when the car comes back.

  • 4 months later...

Be careful when jacking car up to fit front tyres that you dont tighten the wheel nuts up while car is in the air. Locks the front diff up and can result in a car spearing left on 1st launch, and a very dirty racesuit.

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...