Jump to content
SAU Community

Official Team Northside Dinner - Thursday September 27th 2007


Recommended Posts

September Dinner - Naremburn Pizzeria - Naremburn

Ladies and Gents, its time for the next installment of the Official Team Northside Monthly Dinner.

This month, the venue for our monthly feasting will be local favorite, Naremburn Pizzeria, Willougby Rd Naremburn, Sydney.

Plenty of parking is available either right out front or around the back of this venue and its very easy to find, positioned almost exactly halfway between Willoughby and Crows Nest.

Large selection of great Pizza's and Pasta Dishes available so make some space in your diary and be there!

Bookings at Naremburn Pizzeria are essential, so if you would like to attend, please raise your e-hand now to reserve your spot as space is limited. If you wish to attend, you must confirm your attendance beforehand.

Date:

Thursday September 27th, 2007

Time:

7:30pm

Address:

Naremburn Pizzeria

300 Willoughby Road

Naremburn 2065 NSW

Confirmed Attendees:

- Blitz

- Sewid

- Damuscat

- Nissaner

- Liz

- A31Deviat

oh, and this place is really good. I eat there way too much. :(

I don't think I'll be able to make this one (again :) ) as if things go my way I'll be out at Oran Park all day.

oh, and this place is really good. I eat there way too much. :(

I don't think I'll be able to make this one (again :) ) as if things go my way I'll be out at Oran Park all day.

You know your attendance rate is now borderline Mona :laughing-smiley-014:

"Or somebody's gonna get hurt!"

I'd love to come, but I've also already exhausted my funds for the fortnight! I've gotta make sure I can make it through to NEXT weekend.



  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...