Jump to content
SAU Community

Spigot Bush Help Needed

MZTRBO
 Share

Recommended Posts

MZTRBO Experienced

MZTRBO

Posted
Posted

Hi All,

I am converting a r33 gtst from auto to man. I am having trouble getting the auto spigot bush out.

I have tried using the wet newspaper with a bolt trick but its not working at all.

Has any body got a spigot bush puller they can lend for a day, I really need it out as its holding me up.

Also, anyone got any other techniques.

Cheers

Daniel

Link to comment
https://www.sau.com.au/forums/topic/186993-spigot-bush-help-needed/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

Had the same problem converting an auto Stagea engine for a manual box in my 32. The usual method is to fill the hole with grease, then punch a gearbox input shaft into the hole.

However, I ended up resorting to a wheel stud tack-welded onto the bearing, then use a drift hammer to pull it out.

blind_elk Grand Master

blind_elk

Posted
Posted
I have tried the equivalent and to no prevail.

The wheel stud you used, was it a perfect ft into the bush or was there 0.5mm - 1mm gap give or take each side.

Cheers

Don't remember - it was 3 years ago, and I'm suffering advanced dementia :laughing-smiley-014:

It doesn't have to fit - the weld will bridge the gap.

MZTRBO Experienced

MZTRBO

Posted
  • Author
Posted
sorry to ask a dumb question....but why would an auto have a spigot bush? what sits in it?

I assume its in there for the torque converter and this ones a steel item it doesnt wear down, where the manual bush is brass and slowly wears down overtime. I think this is correct :down:

dangerman4 Mentor

dangerman4

Posted
Posted

normally i use grease, but if you cant find a perfect fitting bolt to bash in there try using blue tack.

hasnt failed me yet. and also doesnt destroy the crank if you miss hit with the chisel idea from above..

MZTRBO Experienced

MZTRBO

Posted
  • Author
Posted

I had another go at it today. Went to the bolt shop and got almost a perfect match for it..still wont budge, the newspaper keeps pressing into the thread.

The glue tack idea sounds good. I might try some grease instead of the wet newspaper too.

Cheers

Blue32 Experienced

Blue32

Posted
Posted

For mine I went to the local hardware and bought a suitable size bolt (like 16mm or so as mentioned before), CUT the thread of the end with a hacksaw and cleaned up the edges with a file, then filled the back of the crank with grease and gave it the FBH (f@cken big hammer) approach and it popped out easy as. The bolt has to be a tight fit - ie you have to hit it in with the hammer, and after a short amount of time it came out easy as. Cost me a couple of dollars - tried heaps of other methods before I finally gave this a go - was completely suprised at how easy it was. You then can keep the long bolt 'genuine spiggot bush remover' in your box of tricks for next time. As they say - the right tool makes the job easy! Good luck :-)

OFENSV Proficient

OFENSV

Posted
Posted

you sure the brass bush doent just fit inside of it? i dont see the point of having a bearing for an auto when the crank and torque convertor dont turn in each other unlike an input shaft of a gearbox. ive converted an rb30 auto to a manual and all you have to do is fit the bush

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      ECU sees many times the speed than speedo does (R34 swap)

      By Kapr · Posted

      The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...