Jump to content
SAU Community

Recommended Posts

Hey guys im after a place who can do a dyno run on an R34 GTR, so i need a place with a 4wd dyno!

Can anyone help me out? Around the west and north west would be preffered, but if not its all good, i guess anywhere would be much apreciated!

i no CDN motorworks has one....but im after somewhere else...thnxx

-Ferah

Link to comment
https://www.sau.com.au/forums/topic/188379-4wd-dyno-in-melb/
Share on other sites

*sigh* pipe down, getting quite tired of your shit around here of late.

So ship up or ship out is as simple as it gets.

You dont 'need' a 4WD dyno for a GTR is what i was pointing out, you can take them anywhere.

Just offering an alternate solution which opens up the door to a dozen reasonable workshops out west which might not be realised :)

Time wise if you find anywhere with a RWD place in the west, shaft out, car dyno'd, you'd be back home before you even get off the eastern freeway... let alone Springvale.

OMG OMG RE RE RE

North westside f**kwits !!!!!

look up the dyno dynamics web site or DTS or mainline they have their dyno lactions across victoria.

But yes creatd has a new 4wd one.

http://www.dyno.com.au/dyno/controller/locator/showDealers

Well EAS Performance has dropped the front shafts in many GTR's, for dyno tunning; as Ash stated only takes 10-15 mins.

Vic and George will take good care of the car, as they have done mine for the last 6+ years. Details below, in my sig.

Well EAS Performance has dropped the front shafts in many GTR's, for dyno tunning; as Ash stated only takes 10-15 mins.

Vic and George will take good care of the car, as they have done mine for the last 6+ years. Details below, in my sig.

yepp i showed the owner all of the above numbers and he called and spoke to all of them...looks like EAS it is :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...